TEF6730HW/V1,557 NXP Semiconductors, TEF6730HW/V1,557 Datasheet - Page 14

• Manufacturer Part Number: TEF6730HW/V1,557
• Description: IC DIGITAL IF FRONT END 64HTQFP
• Manufacturer: NXP Semiconductors

Specifications of TEF6730HW/V1,557

• Package / Case: 64-TQFP Exposed Pad, 64-eTQFP, 64-HTQFP, 64-VQFP
• Modulation Or Protocol: AM, FM, WB
• Applications: AM/FM Radio Receiver
• Current - Receiving: 85.3mA, 114.7mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 8 V ~ 9 V
• Operating Temperature: -40°C ~ 85°C
• Bus Type: I2C
• Maximum Agc: 14 dB
• Maximum Frequency: 288 MHz, 108 MHz
• Minimum Frequency: 144 MHz, 65 MHz
• Modulation Technique: AM, FM
• Mounting Style: SMD/SMT
• Function: Radio
• Noise Figure: 12.9 dB, 6.9 dB
• Operating Supply Voltage: 8.5 V
• Supply Voltage (min): 8 V
• Supply Voltage (max): 9 V
• Minimum Operating Temperature: - 40 C
• Maximum Operating Temperature: + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Frequency: -
• Sensitivity: -
• Memory Size: -
• Data Rate - Maximum: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 935278526557; TEF6730HW/V1; TEF6730HW/V1

Philips Semiconductors
TEF6721HL_4
Product data sheet
8.2.6 Write mode: data byte 4
Table 15:
Table 16:
[1]
Table 17:
Table 18:
Table 19:
BND1
0
0
1
1
BND1
0
1
Bit
7
6 and 5
4
3
2
1
0
AGC1
0
0
1
1
KAGC
X = don’t care.
7
FM band selection bits
AM band selection bits
Format of data byte 4
Description of data byte 4 bits
Setting of wideband AGC for AM (m = 0.3)
BND0
0
1
0
1
BND0
X
X
Symbol
KAGC
AGC[1:0]
LODX
FMINJ
-
AGCSW
MIXGAIN
AGC1
6
Rev. 04 — 20 December 2005
Frequency band
FM standard
FM Japan
FM East Europe
FM weather
Frequency band
AM SW
AM LW/MW
Description
Keyed FM AGC. If KAGC = 0, then keyed FM AGC is off. If KAGC = 1,
then keyed FM AGC is on.
Wideband AGC. These 2 bits set the start value of wideband AGC. For
AM, see
Local or distance. If LODX = 0, then distance mode is on. If LODX = 1,
then local mode is on.
FM mixer image rejection. If FMINJ = 0, then low injection. If
FMINJ = 1, then high injection.
This bit is not used and should be set to logic 0.
AGC switch. If AGCSW = 0, then AM AGC in FM mode and FM AGC in
AM mode is off. If AGCSW = 1, then AM AGC PIN diode drive is active in
FM mode and FM AGC PIN diode drive is active in AM mode.
FM mixer gain. If MIXGAIN = 0, then the FM mixer gain is nominal. If
MIXGAIN = 1, then the FM mixer gain is +6 dB.
AGC0
0
1
0
1
AGC0
5
Table 19
[1]
LODX
4
and for FM, see
VCO divider
2
3
3
1
VCO divider
10
20
AM mixer input voltage (peak value) (mV)
275
375
500
625
FMINJ
Car radio tuner front-end for digital IF
3
Table
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
20.
2
-
TEF6721HL
Charge pump current
130 A + 3 mA
130 A + 3 mA
1 mA
300 A
Charge pump current
1 mA
1 mA
AGCSW
1
MIXGAIN
14 of 48
0