MC33596FCAER2 Freescale Semiconductor, MC33596FCAER2 Datasheet - Page 29
![no-image](/images/manufacturer_photos/0/2/262/freescale_semiconductor_sml.jpg)
MC33596FCAER2
Manufacturer Part Number
MC33596FCAER2
Description
IC UHF RECEIVER PLL TUNED 32-QFN
Manufacturer
Freescale Semiconductor
Datasheet
1.MC33596FCAE.pdf
(70 pages)
Specifications of MC33596FCAER2
Frequency
304, 315, 426, 434, 868 & 915MHz
Sensitivity
-104dBm
Data Rate - Maximum
22.4 kBaud
Modulation Or Protocol
FSK, OOK
Applications
General Data Transfer
Current - Receiving
10.3mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Voltage - Supply
2.7 V ~ 3.6 V, 4.5 V ~ 5.5 V
Operating Temperature
-20°C ~ 85°C
Package / Case
32-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Memory Size
-
15
This feature allows for defining two different configurations using two different banks, and for switching
them automatically during wakeup when using a strobe oscillator, or by means of the strobe pin actuation
by the MCU. This automatic feature may be used only in receiver mode; thus allowing fast switching
between any different possible configurations.
15.1 Bit Definition
Two sets of configuration registers are available. They are grouped in two different banks: Bank A and
Bank B. Two bits are used to define which bank represents the state of the component.
Freescale Semiconductor
(Section 10)
*Refer to
2. A high level is applied on STROBE in order to wake the MC33596 and enter receive mode. The
3. CONFB and SEB must be forced to low level to enter configuration mode. Register values are
Proposed solutions to verify these conditions are :
— If the receiver does not wake periodically and it is only controlled by the STROBE pin (strobe
— If the receiver wakes periodically (strobe oscillator enable SOE = 1), the state of the MCU
duration of this state should be greater than the sum of lock time parameter 5.9 and 5.10. Refer to
Section 13, “Configuration
writen into the internal registers of the MC33596. Refer to
and to
STROBE
STROBE
CONFB
CONFB
VCC
VCC
SCLK
SCLK
MOSI
MOSI
MISO
MISO
Configuration Switching
SEB
SEB
oscillator disable SOE = 0), an external pulldown resistor on STROBE is required (see
Figure 43
pins must be defined first and then a power supply must be applied to the MC33596. A
transistor can be used to control the power supply on the VCCIN pin of the MC33596. This
transistor will be driven by an MCU I/O (see
strobe oscillator mode).
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
Figure
3V
3V
0
0
1
1
41.
for a 3 V application schematic).
2
2
Mode.”
N1N0 A4 A3 A2 A1 A0 R/W
N1N0 A4 A3 A2 A1 A0 R/W
Figure 23. Startup sequence
MC33596 Data Sheet, Rev. 4
Figure 44
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
3
3
Section 13, “Configuration
for a 3 V application schematic in
Configuration Switching
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
Mode,”
29