T0790-6CP Atmel, T0790-6CP Datasheet
T0790-6CP
Specifications of T0790-6CP
Related parts for T0790-6CP
T0790-6CP Summary of contents
Page 1
... LO driver and an LO amplifier are also included. The T0790 incorporates internal matching on each RF, IF and LO port to enhance ease of use and to reduce the external components required. The LO input can be driven differentially or single ended ...
Page 2
... Positive RF output; nominal DC voltage is 2.4 V internally biased; input should be AC-coupled 14 GND Ground 15 VCC Supply voltage 16 BBQ- Baseband Q-axis negative input – Paddle Device ground and heat sink, requires good thermal path; RF reference plane T0790 [Preliminary] 2 BBQ BBQ VCC VCC 3 14 GND ...
Page 3
... LO_IN-, LO_IN+ BBI+, BBI-, BBQ+, BBQ STG Symbols R thJA Pin Symbol T0790 [Preliminary] Value 5.5 +10.0 3 -40 to +85 -55 to +150 Value 35 , 600 mV differential drive, I/Q signals in P-P P-P Min. Typ. Max. Unit 4.75 5.0 5. dBm 700 2700 MHz 500 MHz 4 ...
Page 4
... Two tone baseband 5.7 IM3 suppression input at 600 mV differential per tone 5.8 Broadband noise floor 5.9 Quadrature phase error 5.10 I/Q amplitude balance *) Type means 100% tested 100% correlation tested Characterized on samples Design parameter T0790 [Preliminary 600 mV P-P Pin Symbol Min 3.75 ...
Page 5
... Min. 12 2300 RF 12 -18 RFout 12 LORL 12, 13 P1dB 12 LORF 12 12 P-P IM3 12 NOISE 12 12, 13 -0.2 T0790 [Preliminary] differential drive, I/Q signals in P-P Typ. Max. Unit Type* 2000 MHz -11.5 -10.0 dBm dBm -40 -32 dBm -155 -148 dBm/Hz ±0.5 +2 ° ±0.5 +0.2 dB differential drive, I/Q signals in P-P Typ ...
Page 6
... MHz to 1000 MHz: Typical Device Performance T0790 [Preliminary] 6 Figure 3. SSB Power versus LO Frequency - -11 -13 -15 700 750 Figure 4. Output P1dB versus LO Frequency 700 750 Figure 5. Carrier Feedthrough versus LO Frequency -30 -34 -38 -42 -46 -50 700 750 800 850 900 950 1000 LO Frequency (MHz) ...
Page 7
... Figure 7. Intermodulation Distortion versus SSB Output Power 0 -20 -40 -60 -80 -100 -12 -10 -8 Figure 8. RF and LO Return Losses Port 30 40 700 750 T0790 [Preliminary] 800 850 900 950 LO Frequency (MHz) Fundamental (each tone) 3rd intermodulation (each tone BBInput Level (dBVp-p diff.) LO Port 800 850 900 ...
Page 8
... MHz to 2500 MHz: Typical Device Performance T0790 [Preliminary] 8 All tests have been done on a testboard with LO and RF matching to 2600 MHz (see “Application Bard Schematic” description on page 10). Test in a clima chamber required long cables, which added additionall loss and affected the output power. ...
Page 9
... Figure 14. Amplitude Balance versus LO Frequency 0.20 0.18 0.16 0.14 -40°C 0.12 0.10 0.08 0.06 0.04 0.02 0.00 1.5 T0790 [Preliminary] RF port at +85°C LO port at +85°C RF port at +25°C LO port RF port at -40°C at -40°C 2.5 3.0 LO Frequency (GHz) +25°C +85° ...
Page 10
... C 2 LOin SH1 Bill of Materials (700 MHz to 1000 MHz Evaluation Board) Component Direct Quadrature Modulator Inductor Resistor R Resistor Capacitor Capacitor Electrolytic capacitor Capacitor C Capacitor RF transformer 700 MHz to 1300 MHz RF connector Note: 1. May vary due to printed board layout and material. T0790 [Preliminary ...
Page 11
... C8, C11 Panansonic 1 2 Johnson , Components T0790 [Preliminary] Part Number/ (1) Remark Value Size/Package T0790 PSSO16 74476401 1 µH 1210 180 0402 1 k 0402 6.8 pF 0402 1 nF 0402 10 µF Size A 2.7 pF 0402 NC 0402 EHF-FD1619 3216 142-0711-841 SMA Part Number/ (1) Remark Value Size/Package T0790 PSSO16 74476401 1 µ ...
Page 12
... T0790 [Preliminary] 12 Figure 16. Demo Test Board (Fully Assembled PCB) Figure 17. Recommended Package Footprint 1.25 0.30 0.35 0.62 3.0 - Indicates metalization Note: Only ground signal traces are allowed directly under the package. Heatslug must be soldered to GND. Plugging of the ground vias under the heat slug is also recommended to avoid soldering problems ...
Page 13
... Ordering Information Extended Type Number T0790-6C Package Information 4555D–SIGE–05/04 T0790 [Preliminary] Package Remarks PSSO16 – 13 ...
Page 14
... No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. ...