T0790-6CP Atmel, T0790-6CP Datasheet
T0790-6CP
Specifications of T0790-6CP
Related parts for T0790-6CP
T0790-6CP Summary of contents
Page 1
... LO driver and an LO amplifier are also included. The T0790 incorporates internal matching on each RF, IF and LO port to enhance ease of use and to reduce the external components required. The LO input can be driven differentially or single ended ...
Page 2
... Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Supply voltage applied LO input signals Input voltage Operating case temperature Storage temperature T0790 [Preliminary] 2 BBQ VCC GND 3 ...
Page 3
... Type means 100% tested 100% correlation tested Characterized on samples Design parameter 4555B–SIGE–10/03 Symbols R thJA Pin Symbol T0790 [Preliminary] Value 35 , 600 mV differential drive, I/Q signals in P-P P-P Min. Typ. Max. Unit 4.75 5.0 5. dBm 700 2700 MHz 500 MHz 4 11 1.5 V Unit K/W Type* A ...
Page 4
... Matched return loss 1-dB output compression point LO-RF leakage Sideband suppression Two tone baseband IM3 suppression input at 600 mV differential per tone *) Type means 100% tested 100% correlation tested Characterized on samples Design parameter T0790 [Preliminary 600 mV P-P Pin Symbol Min. 12 700 RF 12 -13 ...
Page 5
... RFout 12 LORL 12, 13 P1dB 12 LORF 12 12 P-P IM3 12 NOISE 12 12, 13 -0.2 T0790 [Preliminary] differential drive, I/Q signals in P-P Typ. Max. Unit Type* dBm/ -155 -148 Hz ° ±0.5 +2 ±0.5 +0.2 dB differential drive, I/Q signals in P-P Typ. Max. Unit Type* 2700 MHz -14 ...
Page 6
... MHz to 1000 MHz: Typical Device Performance T0790 [Preliminary] 6 Figure 3. SSB Power versus LO Frequency - -11 -13 -15 700 750 Figure 4. Output P1dB versus LO Frequency Output P1dB vs. LO Frequency 700 750 Figure 5. Carrier Feedthrough versus LO Frequency Carrier Feedthrough vs. LO Frequency -30 -34 -38 -42 -46 -50 700 750 SSB Power vs ...
Page 7
... Figure 7. Intermodulation Distortion versus SSB Output Power Intermodulation Distortion vs. 0 -20 -40 -60 -80 -100 -12 -10 Figure 8. RF and LO Return Losses 700 750 T0790 [Preliminary] 750 800 850 900 950 1000 LO Frequency (MHz) SSB Output Power @ 880 MHz fundamental (each t one) 3rd intermod. (each tone Input Level (dBVp-p diff ...
Page 8
... MHz to 2500 MHz: Typical Device Performance T0790 [Preliminary] 8 All tests have been done on a testboard with LO and RF matching to 2600 MHz (see “Application Bard Schematic” description on page 10). Test in a clima chamber required long cables, which added additionall loss and affected the output power. ...
Page 9
... Figure 14. Amplitude Balance versus LO Frequency 0.20 0.18 0.16 0.14 -40°C 0.12 0.10 0.08 0.06 0.04 0.02 0.00 1.5 T0790 [Preliminary] RF port at +85°C LO port at +85°C RF port at +25°C LO port RF port at -40°C at -40°C 2.5 3.0 LO Frequency (GHz) +25°C +85° ...
Page 10
... Component Direc Quadrature Modulator Inductor Resistor R1, R2, R6, R7 Resistor Capacitor Capacitor Electrolytic capacitor Capacitor C5, C6, C12, C13 Capacitor RF transformer 700 MHz to 1300 MHz RF connector P8, P9, P10, P11, P12, P13 Note: 1. May vary due to printed board layout and material. T0790 [Preliminary VCC ...
Page 11
... Panansonic Johnson Components Reference Vendor D1 Atmel Würth L1 Elektronik R5 C3,C16 C4,C15 C2 C5, C12 C6, C13 C8, C11 T1, T2 Panansonic Johnson Components T0790 [Preliminary] Part Number/ (1) Remark Value Size/Package T0790 SSOP16 74476401 1 µH 1210 180 W 0402 1 kW 0402 6.8 pF 0402 1 nF 0402 10 µF Size A 2.7 pF 0402 n ...
Page 12
... Figure 16. Demo Test Board (Fully Assembled PCB) 2" Figure 17. Recommended Package Footprint 0.30 0.35 Note: Only ground signal traces are allowed directly under the package. Heatslug must be soldered to GND. Plugging of the ground vias under the heat slug is also recommended to avoid soldering problems. T0790 [Preliminary] 12 2" ...
Page 13
... Ordering Information Extended Type Number T0790-6C Package Information 4555B–SIGE–10/03 T0790 [Preliminary] Package Remarks SSOP16 – 13 ...
Page 14
... No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. ...