SA607DK/01,112 NXP Semiconductors, SA607DK/01,112 Datasheet - Page 4

• Manufacturer Part Number: SA607DK/01,112
• Description: IC MIXER FM IF SYSTEM LV 20-SSOP
• Manufacturer: NXP Semiconductors
• Series: SA607r

Specifications of SA607DK/01,112

• Package / Case: 20-SSOP
• Rf Type: Cellular, ASK, FSK, NAMPS, NTACS, VHF
• Frequency: 150MHz
• Number Of Mixers: 2
• Gain: 17dB
• Noise Figure: 6.2dB
• Secondary Attributes: Up Converter
• Current - Supply: 4.2mA
• Voltage - Supply: 2.7 V ~ 7 V
• Maximum Input Frequency: 150 MHz
• Mounting Style: SMD/SMT
• Maximum Operating Frequency: 0.455 MHz
• Maximum Power Gain: 19.5 dB
• Operating Supply Voltage: 3 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 935275287112; SA607DK/01; SA607DK/01

Philips Semiconductors
AC ELECTRICAL CHARACTERISTICS
T
= 3.3k; RF level = –45dBm; FM modulation = 1kHz with 8kHz peak deviation. Audio output with de-emphasis filter and C-message weighted
filter. Test circuit 3. The parameters listed below are tested using automatic test equipment to assure consistent electrical characterristics. The
limits do not represent the ultimate performance limits of the device. Use of an optimized RF layout will improve many of the listed parameters.
NOTE:
1997 Nov 07
1. The generator source impedance is 50 , but the SA607 input impedance at Pin 18 is 1500 . As a result, IF level refers to the actual signal
Mixer/Osc section (ext LO = 220mV
IF section
RF/IF section (int LO)
A
SYMBOL
Low voltage high performance mixer FM IF system
= 25 C; V
that enters the SA607 input (Pin 18) which is about 21dB less than the “available power” at the generator.
f
THD
S/N
OSC
f
IN
CC
Input signal frequency
Crystal oscillator frequency
Noise figure at 45MHz
Third–order input intercept point (50
source)
Conversion power gain
RF input resistance
RF input capacitance
Mixer output resistance
IF amp gain
Limiter gain
Input limiting –3dB, R
AM rejection
Audio level
SINAD sensitivity
Total harmonic distortion
Signal–to–noise ratio
IF RSSI output, R
RSSI range
RSSI accuracy
IF input impedance
IF output impedance
Limiter input impedance
Limiter output impedance
Limiter output level
Frequency check/limiter output impedance
Frequency check/limiter output level
Audio level
System RSSI output
System SINAD sensitivity
= +3V, unless otherwise stated.
PARAMETER
9
= 2k
17
RMS
= 2.4k
1
)
RF frequency = 45MHz + 14.5dBV RF input step-up; IF frequency = 455kHz; R17 = 2.4k; R18
f1 = 45.0; f2 = 45.06MHz
Input RF Level = –52dBm
Matched 14.5dBV step–up
50 source
Single–ended input
(Pin 20)
50 source
50 source
Test at Pin 18
80% AM 1kHz
Gain of two (2k AC load)
RF level –110dB
No modulation for noise
IF level = –118dBm
IF level = –68dBm
IF level = –23dBm
(Pin 11)
(Pin 11)
(Pin 9)
(Pin 9)
3V = V
3V = V
RF level = –117dBm
CC
CC
TEST CONDITIONS
, RF level = –27dBm
, RF level = –27dBm
4
No load
5k load
No load
5k load
13.5
1.25
1.30
MIN
–35
.70
1.2
1.3
70
LIMITS
SA607
–109
TYP
+2.5
+1.5
150
150
120
–50
200
130
115
200
130
115
120
6.2
3.0
1.5
0.3
1.1
1.8
1.5
0.3
1.5
2.2
–9
17
44
58
45
17
62
90
12
8
Product specification
MAX
19.5
1.80
160
4.0
0.8
2.5
SA607
mV
mV
mV
UNITS
MHz
MHz
dBm
dBm
mV
dB
dB
dB
k
k
dB
dB
dB
dB
dB
dB
dB
dB
k
k
k
dB
pF
V
V
V
V
RMS
RMS
RMS