DSP56311VF150 Freescale Semiconductor, DSP56311VF150 Datasheet - Page 14

• Manufacturer Part Number: DSP56311VF150
• Description: IC DSP 24BIT 150MHZ 196-BGA
• Manufacturer: Freescale Semiconductor
• Series: DSP563xxr
• Type: Fixed Pointr

Specifications of DSP56311VF150

• Interface: Host Interface, SSI, SCI
• Clock Rate: 150MHz
• Non-volatile Memory: ROM (576 B)
• On-chip Ram: 384kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.80V
• Operating Temperature: -40°C ~ 100°C
• Mounting Type: Surface Mount
• Package / Case: 196-MAPBGA
• Device Core Size: 24b
• Format: Fixed Point
• Clock Freq (max): 150MHz
• Mips: 150
• Device Input Clock Speed: 150MHz
• Ram Size: 384KB
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (min): 1.7/1.7/3/3/3/3/3/3V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 196
• Package Type: MA-BGA
• Package: 196MA-BGA
• Numeric And Arithmetic Format: Fixed-Point
• Maximum Speed: 150 MHz
• Device Million Instructions Per Second: 150 MIPS
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Signals/Connections
1-10
HDS/HDS
HWR/HWR
PB12
HREQ/HREQ
HTRQ/HTRQ
PB14
HACK/HACK
HRRQ/HRRQ
PB15
Notes:
Signal Name
1.
2.
In the Stop state, the signal maintains the last state as follows:
• If the last state is input, the signal is an ignored input.
• If the last state is output, these lines have weak keepers that maintain the last output state even if the drivers are tri-stated.
The Wait processing state does not affect the signal state.
Input or Output
Input or Output
Input or Output
Output
Output
Output
Type
Input
Input
Input
State During
Ignored Input
Ignored Input
Ignored Input
Table 1-11.
Reset
DSP56311 Technical Data, Rev. 8
1,2
Host Data Strobe—When the HI08 is programmed to interface with a single-
data-strobe host bus and the HI function is selected, this signal is the host data
strobe (HDS) Schmitt-trigger input. The polarity of the data strobe is
programmable but is configured as active-low (HDS) following reset.
Host Write Data—When the HI08 is programmed to interface with a double-
data-strobe host bus and the HI function is selected, this signal is the host write
data strobe (HWR) Schmitt-trigger input. The polarity of the data strobe is
programmable but is configured as active-low (HWR) following reset.
Port B 12—When the HI08 is configured as GPIO through the HI08 Port Control
Register, this signal is individually programmed as an input or output through the
HI08 Data Direction Register.
Host Request—When the HI08 is programmed to interface with a single host
request host bus and the HI function is selected, this signal is the host request
(HREQ) output. The polarity of the host request is programmable but is
configured as active-low (HREQ) following reset. The host request may be
programmed as a driven or open-drain output.
Transmit Host Request—When the HI08 is programmed to interface with a
double host request host bus and the HI function is selected, this signal is the
transmit host request (HTRQ) output. The polarity of the host request is
programmable but is configured as active-low (HTRQ) following reset. The host
request may be programmed as a driven or open-drain output.
Port B 14—When the HI08 is configured as GPIO through the HI08 Port Control
Register, this signal is individually programmed as an input or output through the
HI08 Data Direction Register.
Host Acknowledge—When the HI08 is programmed to interface with a single
host request host bus and the HI function is selected, this signal is the host
acknowledge (HACK) Schmitt-trigger input. The polarity of the host
acknowledge is programmable but is configured as active-low (HACK) after
reset.
Receive Host Request—When the HI08 is programmed to interface with a
double host request host bus and the HI function is selected, this signal is the
receive host request (HRRQ) output. The polarity of the host request is
programmable but is configured as active-low (HRRQ) after reset. The host
request may be programmed as a driven or open-drain output.
Port B 15—When the HI08 is configured as GPIO through the HI08 Port Control
Register, this signal is individually programmed as an input or output through the
HI08 Data Direction Register.
Host Interface (Continued)
Signal Description
Freescale Semiconductor