CU4032K250G2 EPCOS Inc, CU4032K250G2 Datasheet - Page 28

• Manufacturer Part Number: CU4032K250G2
• Description: VARISTOR STD 250VRMS 4032 SMD
• Manufacturer: EPCOS Inc
• Series: CUr

Specifications of CU4032K250G2

• Varistor Voltage: 390V
• Current-surge: 1.2kA
• Number Of Circuits: 1
• Maximum Ac Volts: 250VAC
• Maximum Dc Volts: 320VDC
• Energy: 19J
• Package / Case: Non-Standard SMD
• Technology: Metal Oxide
• Capacitance Value: 105pF
• Clamping Current: 10A
• Clamping Voltage: 650V
• Ac Voltage Rating (max): 250VAC
• Dc Voltage Rating (max): 320VDC
• Operating Temp Range: -40C to 85C
• Mounting: Surface Mount
• Surge Current (max): 1200A
• Size Code: 4032
• Product Length (mm): 10.2mm
• Product Depth (mm): 8mm
• Product Height (mm): 4.5mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: B72660M 251K 72; B72660M0251K072; B72660M251K72

7.5
Thin or insufficient adhesive causes chips to loosen or become disconnected during curing.
Low viscosity of the adhesive causes chips to slip after mounting. It is advised to consult the
manufacturer of the adhesive on proper usage and amounts of adhesive to use.
7.6
Used flux should have less than or equal to 0.1 wt % of halogenated content, since flux residue
after soldering could lead to corrosion of the termination and/or increased leakage current on the
surface of the component. Strong acidic flux must not be used. The amount of flux applied should
be carefully controlled, since an excess may generate flux gas, which in turn is detrimental to sol-
derability.
7.7
Solderability is guaranteed for one year from date of delivery for multilayer varistors, CeraDiodes
and ESD/EMI filters (half a year for chips with AgPd and AgPt terminations) and two years for
SHCV and CU components, provided that components are stored in their original packages.
Storage temperature:
Relative humidity:
The solderability of the external electrodes may deteriorate if SMDs and leaded components are
stored where they are exposed to high humidity, dust or harmful gas (hydrogen chloride, sulfurous
acid gas or hydrogen sulfide).
Do not store SMDs and leaded components where they are exposed to heat or direct sunlight.
Otherwise the packing material may be deformed or SMDs/ leaded components may stick togeth-
er, causing problems during mounting.
After opening the factory seals, such as polyvinyl-sealed packages, it is recommended to use the
SMDs or leaded components as soon as possible.
7.8
Especially in the case of dual-wave soldering, it is of advantage to place the components on the
board before soldering in that way that their two terminals do not enter the solder bath at different
times.
Ideally, both terminals should be wetted simultaneously.
7.9
Please read Cautions and warnings and
Important notes at the end of this document.
SMD disk varistors (CU varistors)
Standard series
An excessively long soldering time or high soldering temperature results in leaching of the outer
electrodes, causing poor adhesion and a change of electrical properties of the varistor due to
the loss of contact between electrodes and termination.
Wave soldering must not be applied for MLVs designated for reflow soldering only.
Keep the recommended down-cooling rate.
Adhesive application
Selection of flux
Storage of CTVSs
Placement of components on circuit board
Soldering cautions
75% annual average, 95% on 30 days a year
25 C to +45 C
Page 28 of 35