TLE4271-2 Infineon Technologies, TLE4271-2 Datasheet - Page 11

• Manufacturer Part Number: TLE4271-2
• Description: IC REGULATOR LDO 5V TO220-7
• Manufacturer: Infineon Technologies

Specifications of TLE4271-2

• Regulator Topology: Positive Fixed
• Voltage - Output: 5V
• Voltage - Input: 6 ~ 40 V
• Voltage - Dropout (typical): 0.35V @ 550mA
• Number Of Regulators: 1
• Current - Output: 550mA (Max)
• Current - Limit (min): 650mA
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Through Hole
• Package / Case: TO-220-7 (Bent and Staggered Leads)
• Number Of Outputs: 1
• Polarity: Positive
• Input Voltage Max: 40 V
• Output Voltage: 5 V
• Output Type: Fixed
• Dropout Voltage (max): 0.7 V at 550 mA
• Output Current: 550 mA
• Load Regulation: 50 mV
• Voltage Regulation Accuracy: 2 %
• Maximum Operating Temperature: + 150 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: SP000013201; SP000306836; TLE42712

Application Description
The IC regulates an input voltage in the range of 6 V <
26 V it produces a regulated output current of more than 550 mA. Above 26 V the save-
operating-area protection allows operation up to 36 V with a regulated output current of
more than 300 mA. Overvoltage protection limits operation at 42 V. The overvoltage
protection hysteresis restores operation if the input voltage has dropped below 36 V. The
IC can be switched off via the inhibit input, which causes the quiescent current to drop
below 10 A. A reset signal is generated for an output voltage of
watchdog circuit monitors a connected controller. If there is no positive-going edge at the
watchdog input within a fixed time, the reset output is set to low. The delay for power-on
reset and the maximum permitted watchdog-pulse period can be set externally with a
capacitor.
Design Notes for External Components
An input capacitor
circuit consisting of lead inductance and input capacitance can be damped by a resistor
of approx. 1
the regulating circuit. Stability is guaranteed at values of
< 3 .
Reset Circuitry
If the output voltage decreases below 4.5 V, an external capacitor
discharged by the reset generator. If the voltage on this capacitor drops below
reset signal is generated on pin RO, i.e. reset output is set low. If the output voltage rises
above the reset threshold,
reset time the voltage on the capacitor reaches
again. The value of the power-on-reset time can be set within a wide range depending
of the capacitance of
Reset Timing
The power-on reset delay time is defined by the charging time of an external capacitor
C
t
Definitions:
•
•
•
•
•
Data Sheet
D
d
=
which can be calculated as follows:
C
t
I
V
D
D
C
V
UD
D
= reset delay time
D
= charge current, typical 14 A
= delay capacitor
=
= upper delay timing threshold at
V
UD
V
/
, typical 1.8 V
I
D
in series with
C
I
C
is necessary for compensation of line influences. The resonant
D
.
C
D
C
will be charged with constant current. After the power-on-
I
. An output capacitor
C
11
D
for reset delay time
V
DU
and the reset output will be set high
C
Q
V
I
is necessary for the stability of
< 40 V to
C
Q
22 F and an ESR of
V
C
Rev. 2.7, 2007-06-25
Qnom
D
V
Q
on pin D will be
= 5.0 V. Up to
< 4.5 V. The
TLE 4271-2
V
DRL
(1)
, a