AS1353-28-T austriamicrosystems, AS1353-28-T Datasheet

no-image

AS1353-28-T

Manufacturer Part Number
AS1353-28-T
Description
IC REG LDO 150MA 2.8V TSOT23-5
Manufacturer
austriamicrosystems
Datasheet

Specifications of AS1353-28-T

Package / Case
SOT-23-5, SC-74A, SOT-25
Mounting Type
Surface Mount
Current - Output
150mA (Min)
Voltage - Output
2.8V
Voltage - Input
Up to 5.5V
Operating Temperature
-40°C ~ 85°C
Regulator Topology
Positive Fixed
Voltage - Dropout (typical)
0.06V @ 150mA
Number Of Regulators
1
Current - Limit (min)
160mA
Primary Input Voltage
3.8V
Output Voltage Fixed
2.8V
Dropout Voltage Vdo
60mV
No. Of Pins
5
Output Current
150mA
Operating Temperature Range
-40°C To +85°C
Filter Terminals
SMD
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AS1353-28-T
Manufacturer:
AMS
Quantity:
30 000
Part Number:
AS1353-28-T
Manufacturer:
austriam
Quantity:
23 000
Part Number:
AS1353-28-T
Manufacturer:
AUSTRIAMICROSY
Quantity:
20 000
A S 1 3 5 3
L i n e a r L o w - D r o p o u t 1 5 0 m A Vo l ta g e R e g u l a t o r s
1 General Description
The AS1353/AS1356 are high-performance, fixed-volt-
age linear LDOs designed for use with capacitors of 1 to
10µF. The devices can deliver superior performance
even under low dropout conditions when the power tran-
sistor operates in linear mode.
The integrated P-channel MOSFET output allows the
devices to maintain a low supply-current at loads of up
to150mA. A shutdown mode includes logic-controlled
circuitry which reduces shutdown current to less than
1µA (max).
Integrated over-temperature and over-current protec-
tion circuitry switches the devices off in case of thermal
overload or output short-circuit conditions.
The AS1353/AS1356 are optimized for low equivalent-
series resistance (ESR) output capacitors. Additionally,
all devices contain reversed battery protection which dis-
connects the internal circuitry and parasitic diodes if the
battery is connected incorrectly.
The AS1356 also features power-OK circuitry which can
be used to monitor output regulation.
All devices also feature an integrated error amplifier and
built-in 1.25V reference, and output current is limited
(380mA typ) via the on-chip current limiting circuitry.
Multiple output voltages are available as standard prod-
ucts: 3.6, 3.3, 3.0, 2.7, 2.5, or 1.5V. All devices are avail-
able in a 5-pin SOT23 package.
Figure 1. Pinout and Application Diagrams
www.austriamicrosystems.com
On
Off
+2.5 to
+5.5V
0.01µF
C
BP
SHDNM
1µF
C
GND
IN
,
IN
A S 1 3 5 6
1
2
3
SHDNM
IN
BP
AS1353
AS1353
GND
OUT
4
5
BP
OUT
C
1µF
OUT
Preset Output
1.5 to 3.6V,
150mA
Revision 1.03
2 Key Features
3 Applications
The devices are ideal for powering cordless and mobile
phones, MP3 players, CD and DVD players, PDAs,
handheld computers, digital cameras, and any other
hand-held and/or battery-powered device.
On
Off
!
!
!
!
!
!
!
!
!
!
!
!
+2.5 to
+5.5V
Ultra-Low Dropout Voltage: 40mV @ 100mA load
Output Voltage Range: +1.5 to +3.6V (100mV steps)
Max Output Current: 150mA
Output Voltage Accuracy: ±1%
Low Shutdown Current: 1µA
High PSRR: 60dB at 100Hz
Integrated Overtemperature/Overcurrent Protection
Reverse-Battery Protection (AS1353/AS1356)
Power-OK Output (AS1356)
Minimal External Components Required
Operating Temperature Range: -40 to +85°C
5-pin SOT23 Package
SHDNM
1µF
C
GND
IN
IN
1
2
3
SHDNM
GND
IN
AS1356
AS1356
OUT
POK
4
5
POK
OUT
100kΩ
C
1µF
OUT
Preset Output
1.5 to 3.6V,
processor
To Micro-
150mA
D a t a S h e e t
1 - 13

Related parts for AS1353-28-T

AS1353-28-T Summary of contents

Page 1

... Integrated over-temperature and over-current protec- tion circuitry switches the devices off in case of thermal overload or output short-circuit conditions. The AS1353/AS1356 are optimized for low equivalent- series resistance (ESR) output capacitors. Additionally, all devices contain reversed battery protection which dis- connects the internal circuitry and parasitic diodes if the battery is connected incorrectly ...

Page 2

... AS1353/AS1356 Data Sheet - Pinout Pin Assignments Figure 2. Pin Assignments (Top View AS1353 GND 2 3 SHDNM Pin Descriptions Table 1. AS1353 Pin Descriptions Pin Number Pin Name GND 3 SHDNM OUT Table 2. AS1356 Pin Descriptions Pin Number Pin Name GND 3 SHDNM 4 POK 5 OUT www.austriamicrosystems.com ...

Page 3

... AS1353/AS1356 Data Sheet - Absolute Maximum Ratings Stresses beyond those listed in Table 3 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in Section 6 Electrical Characteristics on page 4 is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability ...

Page 4

... OUT OUT C = 1µF, OUT f = 10Hz to 100kHz, AS1353 C = 0.01µ 1µF, OUT AS1356 f = 10Hz to 100kHz f = 100Hz 1µF, OUT (C = 0.01µF, AS1353 0.01µF, no load BP (AS1353 +25ºC AMB SHDNM = GND T = +85ºC AMB V = 2 +25ºC AMB SHDNM = IN or GND T = +85º ...

Page 5

... AS1353/AS1356 Data Sheet - Dropout voltage = when V IN OUT ≥ 2.5V). 2. The rise and fall time of the shutdown signal must not exceed 1ms. 3. The delay time is defined as time required to set V 4. Guaranteed by design. www.austriamicrosystems.com is 100mV < V for +0.5V (applies only to output voltages ...

Page 6

... AS1353/AS1356 Data Sheet - Typical Operating Characteristics V = +3. +3.6V OUT , IN IN OUT Figure 3. Ground Pin Current vs. Input Voltage 140 120 I = 150mA OUT 100 I = 0mA OUT Input Voltage (V) Figure 5. Ground Pin Current vs. Temperature 130 150mA IN OUT 120 110 V = 3.6V 150mA IN OUT 100 ...

Page 7

... AS1353/AS1356 Data Sheet - Figure 9. Dropout Voltage vs. Output Load 150 125 100 75 +85° 100 Output Load (mA) Figure 11. Line Transient Response; I 10ms/Div www.austriamicrosystems.com Figure 10. PSRR vs. Frequency +25°C 20 -45° 125 150 10 100 = 50mA OUT Revision 1.03 1000 10000 100000 Frequency (Hz ...

Page 8

... Data Sheet - Detailed Description The AS1353/AS1356 are low-dropout, low-quiescent-current linear regulators intended for LDO regulator applications where output current load requirements range from no load to 150mA. All devices come standard with fixed output volt- ages of 1.5 to 3.6V (see Ordering Information on page Figure 12. Block Diagram ...

Page 9

... If the junction temperature exceeds 165ºC (typ, AS1356) or 150ºC (typ, AS1353), the thermal sensor starts the shut- down logic, at which point the P-channel MOSFET is switched off. After the device temperature has dropped by approximately 20º ...

Page 10

... Power Supply Rejection Ratio The AS1353/AS1356 are designed to deliver low dropout voltages and low quiescent currents. Power-supply rejection is 60dB (typ) at low frequencies. To improve power supply-noise rejection and transient response, increase the values of the input and output bypass capacitors (see Figure 13) ...

Page 11

... AS1353/AS1356 Data Sheet - Package Drawings and Markings The AS1353/AS1356 are available in a 5-pin SOT23 package. Figure 14. 5-pin SOT23 Package Notes: 1. All dimensions in millimeters. 2. Foot length measured at intercept point between datum A and lead surface. 3. Package outline exclusive of mold flash and metal burr. ...

Page 12

... ASD8 LDO 150mA, Reverse-Battery Protection, 1.5V AS1353-18-T ASD9 LDO 150mA, Reverse-Battery Protection, 1.8V AS1353-26-T ASHB LDO 150mA, Reverse-Battery Protection, 2.6V AS1353-28-T ASHC LDO 150mA, Reverse-Battery Protection, 2.8V AS1353-30-T ASHD LDO 150mA, Reverse-Battery Protection, 3.0V AS1353-33-T ASHE LDO 150mA, Reverse-Battery Protection, 3.3V ...

Page 13

... AS1353/AS1356 Data Sheet Copyrights Copyright © 1997-2007, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, trans- lated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. ...

Related keywords