LP38512MRX-ADJ/NOPB National Semiconductor, LP38512MRX-ADJ/NOPB Datasheet - Page 8
![IC REG LDO 1.5A ADJ 8-PSOP](/photos/7/41/74112/pkg_mra08a_sml.jpg)
LP38512MRX-ADJ/NOPB
Manufacturer Part Number
LP38512MRX-ADJ/NOPB
Description
IC REG LDO 1.5A ADJ 8-PSOP
Manufacturer
National Semiconductor
Datasheet
1.LP38512MR-ADJEVNOPB.pdf
(14 pages)
Specifications of LP38512MRX-ADJ/NOPB
Regulator Topology
Positive Adjustable
Voltage - Output
0.5 ~ 4.5 V
Voltage - Input
2.25 ~ 5.5 V
Number Of Regulators
1
Current - Output
1.5A (Max)
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-PSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Dropout (typical)
-
Current - Limit (min)
-
Other names
LP38512MRX-ADJ
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LP38512MRX-ADJ/NOPB
Manufacturer:
NS
Quantity:
1
www.national.com
Block Diagram
Application Information
EXTERNAL CAPACITORS
Like any low-dropout regulator, external capacitors are re-
quired to assure stability. These capacitors must be correctly
selected for proper performance.
Input Capacitor
A ceramic input capacitor of at least 10 µF is required. For
general usage across all load currents and operating condi-
tions, a 10 µF ceramic input capacitor will provide satisfactory
performance.
Output Capacitor
A ceramic capacitor with a minimum value of 10 µF is required
at the output pin for loop stability. It must be located less than
1 cm from the device and connected directly to the output and
ground pin using traces which have no other currents flowing
through them. As long as the minimum of 10 µF ceramic is
met, there is no limitation on any additional capacitance.
X7R and X5R dielectric ceramic capacitors are strongly rec-
ommended, as they typically maintain a capacitance range
within ±20% of nominal over full operating ratings of temper-
ature and voltage. Of course, they are typically larger and
more costly than Z5U/Y5U types for a given voltage and ca-
pacitance.
Z5U and Y5V dielectric ceramics are not recommended as
the capacitance will drop severely with applied voltage. A typ-
ical Z5U or Y5V capacitor can lose 60% of its rated capaci-
tance with half of the rated voltage applied to it. The Z5U and
Y5V also exhibit a severe temperature effect, losing more
than 50% of nominal capacitance at high and low limits of the
temperature range.
REVERSE VOLTAGE
A reverse voltage condition will exist when the voltage at the
output pin is higher than the voltage at the input pin. Typically
this will happen when V
tinues to hold a sufficient charge such that the input to output
IN
is abruptly taken low and C
OUT
con-
8
voltage becomes reversed. A less common condition is when
an alternate voltage source is connected to the output.
There are two possible paths for current to flow from the out-
put pin back to the input during a reverse voltage condition.
While V
the Enable pin is above the V
cuitry will attempt to regulate the output voltage. Since the
input voltage is less than the programmed output voltage, the
control circuit will drive the gate of the pass element to the full
on condition when the output voltage begins to fall. In this
condition, reverse current will flow from the output pin to the
input pin, limited only by the R
the output to input voltage differential. Discharging an output
capacitor up to 1000 µF in this manner will not damage the
device as the current will rapidly decay. However, continuous
reverse current should be avoided. When the Enable is low
this condition will be prevented.
The internal PFET pass element in the LP38512-ADJ has an
inherent parasitic diode. During normal operation, the input
voltage is higher than the output voltage and the parasitic
diode is reverse biased. However, if the output voltage to input
voltage differential is more than 500 mV (typical) the parasitic
diode becomes forward biased and current flows from the
output pin to the input pin through the diode. The current in
the parasitic diode should be limited to less than 1A continu-
ous and 5A peak.
If used in a dual-supply system where the regulator output
load is returned to a negative supply, the output pin must be
diode clamped to ground. A Schottky diode is recommended
for this protective clamp.
SHORT-CIRCUIT PROTECTION
The LP38512-ADJ is short circuit protected, and in the event
of a peak over-current condition the short-circuit control loop
will rapidly drive the output PMOS pass element off. Once the
power pass element shuts down, the control loop will rapidly
cycle the output on and off until the average power dissipation
IN
is high enough to keep the control circuity alive, and
EN(ON)
30040907
DS(ON)
threshold, the control cir-
of the pass element and