LP38512MRX-ADJ/NOPB National Semiconductor, LP38512MRX-ADJ/NOPB Datasheet - Page 4
![IC REG LDO 1.5A ADJ 8-PSOP](/photos/7/41/74112/pkg_mra08a_sml.jpg)
LP38512MRX-ADJ/NOPB
Manufacturer Part Number
LP38512MRX-ADJ/NOPB
Description
IC REG LDO 1.5A ADJ 8-PSOP
Manufacturer
National Semiconductor
Datasheet
1.LP38512MR-ADJEVNOPB.pdf
(14 pages)
Specifications of LP38512MRX-ADJ/NOPB
Regulator Topology
Positive Adjustable
Voltage - Output
0.5 ~ 4.5 V
Voltage - Input
2.25 ~ 5.5 V
Number Of Regulators
1
Current - Output
1.5A (Max)
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-PSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Dropout (typical)
-
Current - Limit (min)
-
Other names
LP38512MRX-ADJ
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LP38512MRX-ADJ/NOPB
Manufacturer:
NS
Quantity:
1
www.national.com
AC Parameters
Thermal Characteristics
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and conditions, see the Electrical Characteristics.
Note 2: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. Test method is per JESD22-A114.
Note 3: Refer to JEDEC J-STD-020C for surface mount device (SMD) package reflow profiles and conditions. Unless otherwise stated, the temperatures and
times are for Sn-Pb (STD) only.
Note 4: Device operation must be evaluated, and derated as needed, based on ambient temperature (T
junction temperature (T
(EIA/JESD51-3). See POWER DISSIPATION/HEAT-SINKING for details.
Note 5: Line regulation is defined as the change in V
Note 6: Load regulation is defined as the change in V
Note 7: The line and load regulation specification contains only the typical number. However, the limits for line and load regulation are included in the output
voltage tolerance specification.
Note 8: Dropout voltage (V
voltage to drop 2%. For the LP38512-ADJ, the minimum operating voltage of 2.25V is the limiting factor when the programed output voltage is less than typically
1.80V.
Symbol
PSRR
ΔT
ρ
T
θ
θ
e
n(l/f)
J-A
J-C
SD
n
SD
Ripple Rejection
Output Noise Density
Output Noise Voltage
Thermal Shutdown
Thermal Shutdown Hysteresis T
Thermal Resistance
Junction to Ambient
(Note 4)
Thermal Resistance
Junction to Case
J(MAX)
DO
), and package thermal resistance (θ
Parameter
) is typically defined as the input to output voltage differential (V
ADJ
ADJ
V
f = 120Hz
V
f = 1 kHz
f = 120Hz
BW = 10Hz - 100kHz
T
PSOP-8
TO-263 THIN
PSOP-8
TO-263 THIN
from the nominal value due to change in the voltage at the input.
from the nominal value due to change in the load current at the output.
IN
IN
J
J
rising
falling from T
= 2.5V
= 2.5V
JA
).The typical θ
Conditions
SD
4
JA
ratings given are worst case based on minimum land area on two-layer PCB
IN
- V
OUT
) where the input voltage is low enough to cause the output
A
), power dissipation (P
Min
-
-
-
-
-
-
-
-
-
-
Typ
165
168
0.4
73
70
25
10
67
11
3
D
), maximum allowable operating
Max
-
-
-
-
-
-
-
-
-
-
µV/
µV
Units
°C/W
°C/W
dB
°C
√
RMS
Hz