LP38690DT-5.0/NOPB National Semiconductor, LP38690DT-5.0/NOPB Datasheet - Page 4

• Manufacturer Part Number: LP38690DT-5.0/NOPB
• Description: IC REG LDO 1A 5.0V TO-252
• Manufacturer: National Semiconductor
• Series: PowerWise®r
• Type: Voltage Regulatorr

Specifications of LP38690DT-5.0/NOPB

• Regulator Topology: Positive Fixed
• Voltage - Output: 5V
• Voltage - Input: Up to 10V
• Voltage - Dropout (typical): 0.45V @ 1A
• Number Of Regulators: 1
• Current - Output: 1A
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: TO-252-2, DPak (2 Leads + Tab), TO-252AA, SC-63
• Current, Output: 1 A
• Current, Supply: 55 μA
• Package Type: TO-252
• Regulation, Line: 0.03 %/V
• Regulation, Load: 1.8 %/A
• Regulator Type: Linear, Low Dropout
• Temperature, Operating, Range: -40 to +125 °C
• Voltage, Dropout: 450 mV
• Voltage, Input: 2.7 to 10 V
• Voltage, Noise: 0.7 μV/sqrt Hz
• Voltage, Output: 5 V
• Voltage, Supply, Rejection Ratio: 55 dB
• Number Of Outputs: 1
• Polarity: Positive
• Input Voltage Max: 10 V
• Output Voltage: 5 V
• Output Type: Fixed
• Dropout Voltage (max): 0.1 V at 100 mA
• Output Current: 1 A
• Line Regulation: 0.03 %/V
• Load Regulation: 1.8 %/A
• Voltage Regulation Accuracy: +/- 2.5 %
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Primary Input Voltage: 10V
• Output Voltage Fixed: 5V
• Dropout Voltage Vdo: 450mV
• No. Of Pins: 3
• Operating Temperature Range: -40°C To +125°C
• Msl: MSL 2 - 1 Year
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Limit (min): -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device
• Other names: *LP38690DT-5.0; *LP38690DT-5.0/NOPB; LP38690DT-5.0

e
V
V
I
EN
n
O
EN
Note 1: Absolute maximum ratings indicate limits beyond which damage to the component may occur. Operating ratings indicate conditions for which the device
is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications, see Electrical Characteristics. Specifications do not
apply when operating the device outside of its rated operating conditions.
Note 2: At elevated temperatures, device power dissipation must be derated based on package thermal resistance and heatsink values (if a heatsink is used).
The junction-to-ambient thermal resistance ( θ
copper area (less than 0.1 square inch). If one square inch of copper is used as a heat dissipator for the TO-252, the θ
SOT-223 package has a θ
when soldered to a copper area of one square inch. The θ
of thermal vias used (refer to application note AN-1187). If power disspation causes the junction temperature to exceed specified limits, the device will go into
thermal shutdown.
Note 3: ESD is tested using the human body model which is a 100pF capacitor discharged through a 1.5k resistor into each pin.
Note 4: Typical numbers represent the most likely parametric norm for 25°C operation.
Note 5: If used in a dual-supply system where the regulator load is returned to a negative supply, the output pin must be diode clamped to ground.
Note 6: Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage.
Note 7: Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from 1mA to full load.
Note 8: Dropout voltage is defined as the minimum input to output differential required to maintain the output within 100mV of nominal value.
Symbol
(LEAK)
Output Noise
Output Leakage Current
Enable Voltage (LP38692 Only)
Enable Pin Leakage
J-A
of approximately 125°C/W when soldered down to a minimum sized pattern (less than 0.1 square inch) and approximately 70°C/W
Parameter
J-A
) for the TO-252 is approximately 90°C/W for a PC board mounting with the device soldered down to minimum
J-A
BW = 10Hz to 10kHz
V
V
Output = OFF
Output = ON, V
Output = ON, V
Output = ON, V
V
values for the LLP package are also dependent on trace area, copper thickness, and the number
O
O
EN
= 3.3V
= V
= 0V or 10V, V
O
(NOM) + 1V @ 10V
Conditions
5
IN
IN
IN
= 4V
= 6V
= 10V
IN
= 10V
IN
MIN
1.8
3.0
4.0
-1
J-A
TYP (Note
drops to approximately 50°C/W. The
0.001
0.7
0.5
4)
MAX
0.4
12
1
µV/
Units
µA
µA
V