TS613IDT STMicroelectronics, TS613IDT Datasheet - Page 4

• Manufacturer Part Number: TS613IDT
• Description: IC AMP DUAL WIDE BAND OP 8 SOIC
• Manufacturer: STMicroelectronics

Specifications of TS613IDT

• Amplifier Type: Voltage Feedback
• Number Of Circuits: 2
• Slew Rate: 40 V/µs
• Gain Bandwidth Product: 130MHz
• Current - Input Bias: 5µA
• Voltage - Input Offset: 1000µV
• Current - Supply: 11mA
• Current - Output / Channel: 320mA
• Voltage - Supply, Single/dual (±): 5 V ~ 12 V, ±2.5 V ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Number Of Channels: 2
• Voltage Gain Db: 80.83 dB
• Common Mode Rejection Ratio (min): 90 dB
• Input Offset Voltage: 6 mV
• Supply Current: 22 mA
• Maximum Power Dissipation: 2000 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Dual Supply Voltage: +/- 6 V
• Minimum Operating Temperature: - 40 C
• Power Supply Requirement: Single/Dual
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-2302-2

TS613
THERMAL INFORMATION
The TS613 is housed in an Exposed-Pad plastic
package. As described on the figures below, this
package uses a leadframe upon which the dice is
mounted. This leadframe is exposed as a thermal
pad on the underside of the package. The thermal
contact is direct with the dice. This thermal path
provide an excellent thermal performance.
The thermal pad is electrically isolated from all
pins in the package. It can also be soldered to a
copper area of the PCB underneath the package.
Through these thermal paths within this copper ar-
ea, heat can be conducted away from the pack-
age. In this case, the copper area must be con-
nected to (-Vcc)
INTERMODULATION DISTORTION
The curves shown below are the measurements
results of a single operator wired as an adder with
a gain of 15dB.
The operational amplifier is supplied by a symmet-
ric 6V and is loaded with 25 .
Two synthesizers (Rhode & Schwartz SME) gen-
erate two frequencies (tones) (70 & 80kHz ; 180 &
280kHz).
An HP3585 spectrum analyzer measures the spu-
rious level at different frequencies.
The curves are traced for different output levels
(the value in the X ax is the value of each tone).
The output levels of the two tones are the same.
The generators and spectrum analyzer are phase
locked to enhance measurement precision.
4/10
Side View
Cross Section View
Bottom View
DICE
3rd ORDER INTERMODULATION
Gain=15dB, Vcc=
80kHz
2nd ORDER INTERMODULATION
Gain=15dB, Vcc=
280kHz, Spurious measurement @100kHz
Gain=15dB, Vcc=
280kHz
3rd ORDER INTERMODULATION
-100
-100
-55
-60
-65
-70
-10
-20
-30
-40
-50
-60
-70
-80
-90
-10
-20
-30
-40
-50
-60
-70
-80
-90
0
0
1,5
1
1
230kHz
1,5
1,5
2
90kHz
80kHz
±
±
±
2
2
6V, RL=25 , 2 tones 70kHz/
6V, RL=25 , 2 tones 180kHz/
6V, RL=25 , 2 tones 180kHz/
380kHz
2,5
60kHz
Vout peak (V)
Vout peak (V)
2,5
2,5
Vout peak (V)
220kHz
3
640kHz
3
3
740kHz
3,5
3,5
3,5
4
4
4
4,5
4,5
4,5