LM2904D STMicroelectronics, LM2904D Datasheet - Page 6

• Manufacturer Part Number: LM2904D
• Description: IC OP AMP DUAL LO POWER 8-SOIC
• Manufacturer: STMicroelectronics

Specifications of LM2904D

• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Slew Rate: 0.6 V/µs
• Gain Bandwidth Product: 1.1MHz
• Current - Input Bias: 20nA
• Voltage - Input Offset: 2000µV
• Current - Supply: 700µA
• Current - Output / Channel: 40mA
• Voltage - Supply, Single/dual (±): 3 V ~ 30 V, ±1.5 V ~ 15 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Number Of Channels: 2
• Common Mode Rejection Ratio (min): 70 dB
• Input Offset Voltage: 7 mV
• Input Bias Current (max): 150 nA
• Operating Supply Voltage: 5 V, 9 V, 12 V, 15 V
• Supply Current: 1.2 mA
• Maximum Power Dissipation: 500 mW
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Dual Supply Voltage: +/- 3 V, +/- 5 V, +/- 9 V, +/- 12 V
• Maximum Dual Supply Voltage: +/- 15 V
• Minimum Dual Supply Voltage: +/- 1.5 V
• Mounting Style: SMD/SMT
• Shutdown: No
• Supply Voltage (max): 30 V
• Supply Voltage (min): 3 V
• Technology: Bipolar
• Voltage Gain Db: 100 dB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Electrical characteristics
Table 3.
1.
2. The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output,
3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3 V.
4. Due to the proximity of external components ensure that stray capacitance does not cause coupling between these
6/21
V
Symbol
O1
GBP
THD
so there is no change in the loading charge on the input lines.
The upper end of the common-mode voltage range is V
damage.
external parts. This typically can be detected at higher frequencies because this type of capacitance increases.
V
SR
V
e
OL
/V
O
n
= 1.4 V, R
O2
Low level output voltage (R
Slew rate
Gain bandwidth product f = 100 kHz
Total harmonic distortion
Equivalent input noise voltage
f = 1 kHz, R
Channel separation
T
T
V
unity gain
T
V
f = 1 kHz, A
C
1 kHz ≤ f ≤ 20 kHz
V
amb
min
min
CC+
CC+
L
CC+
S
= 100 pF, V
= 0 Ω, 5 V < V
≤ T
≤ T
= +25° C
= 15 V, V
= 30 V, V
= 5 V, V
amb
amb
S
= 100 Ω , V
V
≤ T
≤ T
= 20 dB, R
CC+
in
in
max
max
CC-
CC+
= 0.5 to 3 V, R
= 10 mV, R
(4)
= 30 V
= ground, V
Parameter
< 30 V, 0 V < V
CC+
L
L
= 2 kΩ , V
= 30 V
= 10 kΩ)
L
= 2 kΩ , C
L
= 2 kΩ , C
O
ic
Doc ID 2471 Rev 13
o
< V
= 1.4 V, T
= 2 V
CC+
L
CC+
= 100 pF
pp
L
- 1.5 V.
–1.5 V, but either or both inputs can go to +32 V without
=100 pF,
,
amb
= 25° C (unless otherwise specified)
Min.
0.3
0.2
0.7
Typ.
0.02
120
0.6
1.1
55
5
LM2904, LM2904A
Max.
20
20
nV/
MHz
Unit
V/µs
mV
dB
%
√
Hz