LM2902D STMicroelectronics, LM2902D Datasheet - Page 3

• Manufacturer Part Number: LM2902D
• Description: IC OP AMP QUAD LOW POWER 14-SOIC
• Manufacturer: STMicroelectronics

Specifications of LM2902D

• Amplifier Type: General Purpose
• Number Of Circuits: 4
• Slew Rate: 0.4 V/µs
• Gain Bandwidth Product: 1.3MHz
• Current - Input Bias: 20nA
• Voltage - Input Offset: 2000µV
• Current - Supply: 1.5mA
• Current - Output / Channel: 20mA
• Voltage - Supply, Single/dual (±): 3 V ~ 30 V, ±1.5 V ~ 15 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Number Of Channels: 4
• Common Mode Rejection Ratio (min): 70 dB
• Input Offset Voltage: 7 mV
• Input Bias Current (max): 150 nA
• Operating Supply Voltage: 5 V, 9 V, 12 V, 15 V
• Supply Current: 1.2 mA
• Maximum Power Dissipation: 400 mW
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Dual Supply Voltage: +/- 3 V, +/- 5 V, +/- 9 V, +/- 12 V
• Maximum Dual Supply Voltage: +/- 15 V
• Minimum Dual Supply Voltage: +/- 1.5 V
• Mounting Style: SMD/SMT
• Shutdown: No
• Supply Voltage (max): 30 V
• Supply Voltage (min): 3 V
• Technology: Bipolar
• Voltage Gain Db: 100 dB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

LM2902
2
Table 1.
1. All voltage values, except differential voltage are with respect to network ground terminal.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
3. Short-circuit from the output to V
4. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base
5. R
6. Human body model: A 100pF capacitor is charged to the specified voltage, then discharged through a 1.5kΩ resistor
7. Machine model: A 200pF capacitor is charged to the specified voltage, then discharged directly between two pins of the
8. Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly
is approximately 20mA, independent of the magnitude of V
junction of the input PNP transistor becoming forward biased and thereby acting as input diodes clamps. In addition to this
diode action, there is also NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the
op-amps to go to the V
negative. This is not destructive and normal output will set up again for input voltage higher than -0.3V.
between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating.
device with no external series resistor (internal resistor < 5Ω). This is done for all couples of connected pin combinations
while the other pins are floating.
to the ground through only one pin. This is done for all pins.
Symbol
thja/c
R
ESD
R
V
T
V
V
I
T
CC
stg
thja
thjc
in
id
in
j
are typical values.
Absolute maximum ratings
Absolute maximum ratings (AMR)
Supply voltage
Differential input voltage
Input voltage
Output short-circuit duration
Maximum junction temperature
Input current
Storage temperature range
Thermal resistance junction to ambient
Thermal resistance junction to case
HBM: human body model
MM: machine model
CDM: charged device model
SO-14
TSSOP14
DIP14
SO-14
TSSOP14
DIP14
CC
voltage level (or to ground for a large overdrive) for the time duration than an input is driven
(4)
CC
(1)
+
can cause excessive heating and eventual destruction. The maximum output current
(7)
Parameter
(2)
(6)
(8)
(3)
(5)
CC
(5)
+
.
-65 to +150
-0.3 to +32
±16 to 33
Infinite
Value
1500
+32
150
105
100
370
150
Absolute maximum ratings
50
80
31
32
33
°C/W
°C/W
Unit
mA
°C
°C
V
V
V
V
V
V
s
3/16