LT1210CR#PBF Linear Technology, LT1210CR#PBF Datasheet - Page 3

• Manufacturer Part Number: LT1210CR#PBF
• Description: IC 35MHZ 1.1 AMP AMPLIFIER 7 DD
• Manufacturer: Linear Technology
• Type: Current Feedback Amplifierr

Specifications of LT1210CR#PBF

• Amplifier Type: Current Feedback
• Number Of Circuits: 1
• Slew Rate: 90 V/µs
• -3db Bandwidth: 55MHz
• Current - Input Bias: 10µA
• Voltage - Input Offset: 3000µV
• Current - Supply: 35mA
• Current - Output / Channel: 2A
• Voltage - Supply, Single/dual (±): 10 V ~ 30 V, ±5 V ~ 15 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: TO-263-7, D²Pak (7 leads + Tab), TO-263CA
• Rail/rail I/o Type: No
• Number Of Elements: 1
• Common Mode Rejection Ratio: 55dB
• Input Offset Voltage: 15mV
• Single Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (typ): ±9/±12V
• Voltage Gain In Db: 71dB
• Power Supply Rejection Ratio: 60dB
• Power Supply Requirement: Dual
• Shut Down Feature: Yes
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): ±5V
• Dual Supply Voltage (max): ±15V
• Technology: Bipolar
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 7 +Tab
• Package Type: DDPAK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Gain Bandwidth Product: -
• Lead Free Status / Rohs Status: Compliant

temperature range, otherwise specifications are at T
otherwise noted.
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Applies to short circuits to ground only. A short circuit between
the output and either supply may permanently damage the part when
operated on supplies greater than ±10V.
Note 3: Commercial grade parts are designed to operate over the
temperature range of – 40°C ≤ T
guaranteed beyond 0°C ≤ T
– 40°C ≤ T
SYMBOL
CMRR
PSRR
A
R
V
I
I
SR
BW
ELECTRICAL CHARACTERISTICS
OUT
S
V
OL
OUT
A
≤ 85°C are available on special request. Consult factory.
PARAMETER
Common Mode Rejection Ratio
Inverting Input Current
Common Mode Rejection
Power Supply Rejection Ratio
Noninverting Input Current
Power Supply Rejection
Inverting Input Current
Power Supply Rejection
Large-Signal Voltage Gain
Transresistance, ∆V
Maximum Output Voltage Swing
Maximum Output Current (Note 4)
Supply Current (Note 4)
Supply Current, R
Positive Supply Current, Shutdown
Output Leakage Current, Shutdown
Slew Rate (Note 6)
Slew Rate (Note 4)
Differential Gain (Notes 4, 7)
Differential Phase (Notes 4, 7)
Small-Signal Bandwidth
A
≤ 70°C. Industrial grade parts tested over
SD
A
OUT
= 51k (Notes 4, 5)
≤ 85°C, but are neither tested nor
/∆I
IN
–
CONDITIONS
V
V
V
V
V
V
V
T
R
V
V
T
R
V
V
T
T
V
T
T
V
V
T
T
V
V
A
R
A
R
A
A
A
A
A
A
A
A
S
S
S
S
S
S
S
L
S
S
L
S
S
S
S
S
S
S
V
F
V
F
= 25°C, V
= 25°C, V
= 25°C, V
= 25°C, V
= 25°C, V
= 25°C, V
= 25°C, A
= 25°C, A
= ±15V, V
= ±5V, V
= ±15V, V
= ±5V, V
= ±5V to ±15V
= ±5V to ±15V
= ±5V to ±15V
= 10Ω (Note 3)
= ±15V, V
= ±5V, V
= 10Ω (Note 3)
= ±15V, V
= ±5V, V
= ±15V, R
= ±15V, V
= ±15V, V
= ±15V, R
= ±15V, R
= 2, V
= R
= 2, V
= R
A
G
G
= 25°C. V
= 680Ω, R
= 576Ω, R
S
S
= ±15V, Peaking ≤ 1dB,
= ±15V, Peaking ≤ 1dB,
The
CM
CM
OUT
OUT
S
S
S
S
S
S
V
V
CM
CM
OUT
OUT
SD
SD
L
F
F
= ±15V, V
= ±15V, V
= ±15V, R
= ±5V, R
= ±15V, V
= ±15V
= 2, R
= 2, R
= 750Ω, R
= 750Ω, R
= 1Ω
= ±2V
= ±2V
= ±2V, R
= ±2V, R
= 15V
●
= 15V
= ±12V
= ±12V
= ±8.5V, R
= ±8.5V, R
CM
denotes specifications which apply over the full operating
L
L
L
L
= 100Ω
= 10Ω
= 0V, ±5V ≤ V
= 400Ω
= 10Ω
L
OUT
OUT
SD
L
Note 4: SO package is recommended for ±5V supplies only, as the power
dissipation of the SO package limits performance on higher supplies. For
supply voltages greater than ±5V, use the TO-220 or DD package. See
“Thermal Considerations” in the Applications Information section for
details on calculating junction temperature. If the maximum dissipation of
the package is exceeded, the device will go into thermal shutdown.
Note 5: R
Note 6: Slew rate is measured at ±5V on a ±10V output signal while
operating on ±15V supplies with R
Note 7: NTSC composite video with an output level of 2V.
= 10Ω
L
L
G
G
= 10Ω (Note 3)
= 10Ω
= 10Ω
= 0V
= 750Ω, R
= 750Ω, R
L
L
= ±10V,
= ±10V,
= 10Ω (Note 3)
= 10Ω (Note 3)
SD
is connected between the Shutdown pin and ground.
S
L
L
≤ ±15V, pulse tested, V
= 15Ω
= 15Ω
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
±10.0
F
±2.5
±2.0
MIN
100
400
±8.5
1.1
55
50
60
55
55
55
75
75
= 1.5k, R
SD
±11.5
G
= 0V, unless
±3.0
TYP
260
200
200
900
900
0.1
0.1
0.7
2.0
0.3
0.1
62
60
77
30
71
68
68
35
15
55
35
= 1.5k and R
MAX
500
200
10
10
50
65
30
10
5
LT1210
L
= 400Ω.
UNITS
µA/V
µA/V
nA/V
µA/V
1210fa
3
V/µs
V/µs
MHz
MHz
DEG
mA
mA
mA
kΩ
kΩ
kΩ
dB
dB
dB
dB
dB
dB
µA
µA
%
V
V
V
V
A