TL062CDT STMicroelectronics, TL062CDT Datasheet - Page 3

• Manufacturer Part Number: TL062CDT
• Description: IC AMP LP J-FET DUAL OP 8 SOIC
• Manufacturer: STMicroelectronics

Specifications of TL062CDT

• Amplifier Type: J-FET
• Number Of Circuits: 2
• Slew Rate: 3.5 V/µs
• Gain Bandwidth Product: 1MHz
• Current - Input Bias: 30pA
• Voltage - Input Offset: 3000µV
• Current - Supply: 200µA
• Current - Output / Channel: 20mA
• Voltage - Supply, Single/dual (±): 6 V ~ 36 V, ±3 V ~ 18 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Bandwidth: 1 MHz
• Common Mode Rejection Ratio: 76
• Current, Input Bias: 30 pA
• Current, Input Offset: 5 pA
• Current, Output: 20 mA
• Current, Supply: 200 μA
• Number Of Amplifiers: Dual
• Package Type: SO-8
• Power Dissipation: 680 mW
• Resistance, Input: 10^12 Ohms
• Signal Gain: 6 V/mV
• Temperature, Operating, Range: 0 to +70 °C
• Time, Rise: 0.2 μs
• Voltage, Input: ±15 V
• Voltage, Noise: 42 nV/sqrt Hz
• Voltage, Offset: 3 mV
• Voltage, Supply: 6 to 36 V
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device
• Other names: 497-2194-2

TL062, TL062A, TL062B
2
Table 1.
1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages
2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.
3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure
5. Short-circuits can cause excessive heating and destructive dissipation.
6. Rth are typical values.
7. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for all couples of pin
8. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the
9. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to
Table 2.
Symbol
Symbol
R
ESD
T
R
where the zero reference level is the midpoint between V
that the dissipation rating is not exceeded.
combinations with other pins floating.
device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins
floating.
the ground.
V
V
T
P
V
oper
V
CC
thja
thjc
CC
stg
tot
id
i
Supply voltage
Input voltage
Differential input voltage
Power dissipation
Output short-circuit duration
Storage temperature range
Thermal resistance junction to
ambient
Thermal resistance junction to
case
HBM: human body model
MM: machine model
CDM: charged device model
Supply voltage range
Operating free-air temperature range
Absolute maximum ratings and operating conditions
Absolute maximum ratings
Operating conditions
SO-8
DIP8
SO-8
DIP8
(5) (6)
(5) (6)
Parameter
(2)
Parameter
(1)
(8)
(3)
(7)
(9)
(4)
Doc ID 2294 Rev 3
TL062M, AM, BM TL062I, AI, BI
TL062M, AM, BM TL062I, AI, BI
Absolute maximum ratings and operating conditions
CC
-65 to +150
-55 to +125
+
and V
CC
-
.
-65 to +150
-40 to +105
Infinite
6 to 36
Value
±18
±15
±30
680
125
900
150
1.5
85
40
41
TL062C, AC, BC
TL062C, AC, BC
-65 to +150
0 to +70
°C/W
°C/W
Unit
Unit
mW
°C
kV
°C
V
V
V
V
V
V
3/16