SAF-XC167CI-32F20F BB-A Infineon Technologies, SAF-XC167CI-32F20F BB-A Datasheet - Page 52
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
SAF-XC167CI-32F20F BB-A
Manufacturer Part Number
SAF-XC167CI-32F20F BB-A
Description
IC MCU 16BIT 256KB TQFP-144-19
Manufacturer
Infineon Technologies
Series
XC16xr
Datasheet
1.SAF-XC167CI-32F20F_BB-A.pdf
(90 pages)
Specifications of SAF-XC167CI-32F20F BB-A
Core Processor
C166SV2
Core Size
16-Bit
Speed
20MHz
Connectivity
CAN, EBI/EMI, I²C, SPI, UART/USART
Peripherals
PWM, WDT
Number Of I /o
103
Program Memory Size
256KB (256K x 8)
Program Memory Type
FLASH
Ram Size
12K x 8
Voltage - Supply (vcc/vdd)
2.35 V ~ 2.7 V
Data Converters
A/D 16x8/10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
144-LFQFP
For Use With
B158-H8963-X-X-7600IN - KIT EASY XC167CIMCBX167-NET - BOARD EVAL INFINEON CAN/ETHRNTMCBXC167-BASIC - BOARD EVAL BASIC INFINEON XC16X
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
FX167CI32F20FBBANT
FX167CI32F20FBBAXT
SAFXC167CI32F20FBBAT
SP000098776
SP000224700
FX167CI32F20FBBAXT
SAFXC167CI32F20FBBAT
SP000098776
SP000224700
3.16
The Clock Generation Unit uses a programmable on-chip PLL with multiple prescalers
to generate the clock signals for the XC167 with high flexibility. The master clock
the reference clock signal, and is used for TwinCAN and is output to the external system.
The CPU clock
directly (1:1) or via a 2:1 prescaler (
The on-chip oscillator can drive an external crystal or accepts an external clock signal.
The oscillator clock frequency can be multiplied by the on-chip PLL (by a programmable
factor) or can be divided by a programmable prescaler factor.
If the bypass mode is used (direct drive or prescaler) the PLL can deliver an independent
clock to monitor the clock signal generated by the on-chip oscillator. This PLL clock is
independent from the XTAL1 clock. When the expected oscillator clock transitions are
missing the Oscillator Watchdog (OWD) activates the PLL Unlock/OWD interrupt node
and supplies the CPU with an emergency clock, the PLL clock signal. Under these
circumstances the PLL will oscillate with its basic frequency.
The oscillator watchdog can be disabled by switching the PLL off. This reduces power
consumption, but also no interrupt request will be generated in case of a missing
oscillator clock.
Note: At the end of an external reset (EA = ‘0’) the oscillator watchdog may be disabled
3.17
The XC167 provides up to 103 I/O lines which are organized into nine input/output ports
and one input port. All port lines are bit-addressable, and all input/output lines are
individually (bit-wise) programmable as inputs or outputs via direction registers. The I/O
ports are true bidirectional ports which are switched to high impedance state when
configured as inputs. The output drivers of some I/O ports can be configured (pin by pin)
for push/pull operation or open-drain operation via control registers. During the internal
reset, all port pins are configured as inputs (except for pin RSTOUT).
The edge characteristics (shape) and driver characteristics (output current) of the port
drivers can be selected via registers POCONx.
The input threshold of some ports is selectable (TTL or CMOS like), where the special
CMOS like input threshold reduces noise sensitivity due to the input hysteresis. The
input threshold may be selected individually for each byte of the respective ports.
All port lines have programmable alternate input or output functions associated with
them. All port lines that are not used for these alternate functions may be used as general
purpose IO lines.
Data Sheet
via hardware by (externally) pulling the RD line low upon a reset, similar to the
standard reset configuration.
Clock Generation
Parallel Ports
f
CPU
and the system clock
f
SYS
=
f
f
50
CPU
SYS
=
are derived from the master clock either
f
MC
/ 2). See also
Functional Description
Section
XC167CI-32F
Derivatives
V1.1, 2006-08
4.4.1.
f
MC
is