SAF-XC164CS-32F20F BB-A Infineon Technologies, SAF-XC164CS-32F20F BB-A Datasheet - Page 57

• Manufacturer Part Number: SAF-XC164CS-32F20F BB-A
• Description: IC MCU 16BIT FLASH TQFP-100-16
• Manufacturer: Infineon Technologies
• Series: XC16xr

Specifications of SAF-XC164CS-32F20F BB-A

• Core Processor: C166SV2
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, EBI/EMI, SPI, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 79
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.7 V
• Data Converters: A/D 14x8/10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LFQFP
• Packages: PG-TQFP-100
• Max Clock Frequency: 20.0 MHz
• Sram (incl. Cache): 12.0 KByte
• Can Nodes: 2
• A / D Input Lines (incl. Fadc): 14
• Program Memory: 256.0 KByte
• For Use With: B158-H8962-X-X-7600IN - KIT EASY XC164CSMCBX167-NET - BOARD EVAL INFINEON CAN/ETHRNTMCBXC167-BASIC - BOARD EVAL BASIC INFINEON XC16X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: FX164CS32F20FBBANT; FX164CS32F20FBBAXT; SAFXC164CS32F20FBBAT; SP000098787; SP000224590

Table 11
Parameter
Level inactive hold
current
Level active hold
current
XTAL1 input current
Pin capacitance
(digital inputs/outputs)
1) Keeping signal levels within the limits specified in this table, ensures operation without overload conditions.
2) If XTAL1 is driven by a crystal, reaching an amplitude (peak to peak) of 0.4 ×
3) This parameter is tested for P3, P4, P9.
4) The maximum deliverable output current of a port driver depends on the selected output driver mode, see
5) As a rule, with decreasing output current the output levels approach the respective supply level (
6) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
7) An additional error current (
8) The driver of P3.15 is designed for faster switching, because this pin can deliver the reference clock for the
9) This specification is valid during Reset for configuration on RD, WR, EA, PORT0
10) The maximum current may be drawn while the respective signal line remains inactive.
11) The minimum current must be drawn to drive the respective signal line active.
12) This specification is valid during Reset for configuration on ALE.
13) This specification is valid during Reset for pins P4.3-0, which can act as CS outputs, and for P3.12.
14) Not subject to production test - verified by design/characterization.
Data Sheet
For signal levels outside these specifications, also refer to the specification of the overload current
Table
V
output will float and the voltage results from the external circuitry.
the definition of the overload coupling factor
bus interface (CLKOUT). The maximum leakage current for P3.15 is, therefore, increased to 1 µA.
OH
→
13)
13)
12,
V
DDP
Current Limits for Port Output
). However, only the levels for nominal output currents are guaranteed.
DC Characteristics (Operating Conditions apply)
14)
I
Symbol
I
I
I
C
INJ
LHI
LHA
IL
IO
) will flow if an overload current flows through an adjacent pin. Please refer to
10)
11)
CC –
CC –
Drivers. The limit for pin groups must be respected.
K
OV
Min.
–
-100
.
55
Limit Values
Max.
-10
–
±20
10
V
Unit Test Condition
µA
µA
µA
pF
1)
Electrical Parameters
DDI
(cont’d)
is sufficient.
V
V
V
0 V <
–
OUT
DDP
OUT
Derivatives
V1.1, 2006-08
= 0.5 ×
= 0.45 V
V
XC164-32
IN
V
<
OL
I
OV
V
→
.
DDI
V
SS
,