C8051F005 Silicon Laboratories Inc, C8051F005 Datasheet - Page 79

• Manufacturer Part Number: C8051F005
• Description: IC 8051 MCU 32K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F00xr

Specifications of C8051F005

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

10.4.5. Interrupt Register Descriptions
The SFRs used to enable the interrupt sources and set their priority level are described below. Refer to the datasheet
section associated with a particular on-chip peripheral for information regarding valid interrupt conditions for the
peripheral and the behavior of its interrupt-pending flag(s).
79
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
R/W
Bit7
EA
This bit globally enables/disables all interrupts. It overrides the individual interrupt mask
settings.
0: Disable all interrupt sources.
1: Enable each interrupt according to its individual mask setting.
IEGF0: General Purpose Flag 0.
This is a general purpose flag for use under software control.
This bit sets the masking of the Timer 2 interrupt.
0: Disable all Timer 2 interrupts.
1: Enable interrupt requests generated by the TF2 flag (T2CON.7)
This bit sets the masking of the Serial Port (UART) interrupt.
0: Disable all UART interrupts.
1: Enable interrupt requests generated by the R1 flag (SCON.0) or T1 flag (SCON.1).
This bit sets the masking of the Timer 1 interrupt.
0: Disable all Timer 1 interrupts.
1: Enable interrupt requests generated by the TF1 flag (TCON.7).
This bit sets the masking of external interrupt 1.
0: Disable external interrupt 1.
1: Enable interrupt requests generated by the /INT1 pin.
This bit sets the masking of the Timer 0 interrupt.
0: Disable all Timer 0 interrupts.
1: Enable interrupt requests generated by the TF0 flag (TCON.5).
This bit sets the masking of external interrupt 0.
0: Disable external interrupt 0.
1: Enable interrupt requests generated by the /INT0 pin.
EA: Enable All Interrupts.
ET2: Enable Timer 2 Interrupt.
ES: Enable Serial Port (UART) Interrupt.
ET1: Enable Timer 1 Interrupt.
EX1: Enable External Interrupt 1.
ET0: Enable Timer 0 Interrupt.
EX0: Enable External Interrupt 0.
IEGF0
R/W
Bit6
R/W
ET2
Bit5
Figure 10.9. IE: Interrupt Enable
R/W
Bit4
ES
Rev. 1.7
ET1
R/W
Bit3
EX1
R/W
Bit2
R/W
ET0
Bit1
(bit addressable)
EX0
R/W
Bit0
0xA8
SFR Address:
Reset Value
00000000