MC68HC908GZ8MFJ Freescale Semiconductor, MC68HC908GZ8MFJ Datasheet - Page 61

• Manufacturer Part Number: MC68HC908GZ8MFJ
• Description: IC MCU 8K FLASH 8MHZ CAN 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908GZ8MFJ

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 32-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

4.3.1 Crystal Oscillator Circuit
The crystal oscillator circuit consists of an inverting amplifier and an external crystal. The OSC1 pin is the
input to the amplifier and the OSC2 pin is the output. The SIMOSCEN signal from the system integration
module (SIM) or the OSCSTOPENB bit in the CONFIG register enable the crystal oscillator circuit.
The CGMXCLK signal is the output of the crystal oscillator circuit and runs at a rate equal to the crystal
frequency. CGMXCLK is then buffered to produce CGMRCLK, the PLL reference clock.
CGMXCLK can be used by other modules which require precise timing for operation. The duty cycle of
CGMXCLK is not guaranteed to be 50% and depends on external factors, including the crystal and related
external components. An externally generated clock also can feed the OSC1 pin of the crystal oscillator
circuit. Connect the external clock to the OSC1 pin and let the OSC2 pin float.
4.3.2 Phase-Locked Loop Circuit (PLL)
The PLL is a frequency generator that can operate in either acquisition mode or tracking mode, depending
on the accuracy of the output frequency. The PLL can change between acquisition and tracking modes
either automatically or manually.
4.3.3 PLL Circuits
The PLL consists of these circuits:
The operating range of the VCO is programmable for a wide range of frequencies and for maximum
immunity to external noise, including supply and CGMXFC noise. The VCO frequency is bound to a range
from roughly one-half to twice the center-of-range frequency, f
CGMXFC pin changes the frequency within this range. By design, f
center-of-range frequency, f
(L × 2
CGMRCLK is the PLL reference clock, a buffered version of CGMXCLK. CGMRCLK runs at a frequency,
f
programmable modulo divider. The modulo divider reduces the VCO clock by a factor, N. The dividers
output is the VCO feedback clock, CGMVDV, running at a frequency, f
information, see
The phase detector then compares the VCO feedback clock, CGMVDV, with the final reference clock,
CGMRDV. A correction pulse is generated based on the phase difference between the two signals. The
loop filter then slightly alters the DC voltage on the external capacitor connected to CGMXFC based on
the width and direction of the correction pulse. The filter can make fast or slow corrections depending on
its mode, described in
reference frequency determines the speed of the corrections and the stability of the PLL.
The lock detector compares the frequencies of the VCO feedback clock, CGMVDV, and the reference
clock, CGMRCLK. Therefore, the speed of the lock detector is directly proportional to the reference
Freescale Semiconductor
RCLK
•
•
•
•
•
. The VCO’s output clock, CGMVCLK, running at a frequency, f
E
Voltage-controlled oscillator (VCO)
Modulo VCO frequency divider
Phase detector
Loop filter
Lock detector
)f
NOM
.
4.3.6 Programming the
4.3.4 Acquisition and Tracking
NOM
MC68HC908GZ16 • MC68HC908GZ8 Data Sheet, Rev. 4
, (71.4 kHz) times a linear factor, L, and a power-of-two factor, E, or
PLL.
Modes. The value of the external capacitor and the
VRS
. Modulating the voltage on the
VRS
VCLK
VDV
is equal to the nominal
, is fed back through a
= f
VCLK
/(N). For more
Functional Description
61