ATMEGA328P-MU Atmel, ATMEGA328P-MU Datasheet - Page 44

• Manufacturer Part Number: ATMEGA328P-MU
• Description: MCU AVR 32K FLASH 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA328P-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Controller Family/series: AVR MEGA
• No. Of I/o's: 23
• Eeprom Memory Size: 1KB
• Ram Memory Size: 2KB
• Cpu Speed: 20MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVR
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.11
9.11.1
8271C–AVR–08/10
Register Description
SMCR – Sleep Mode Control Register
The Sleep Mode Control Register contains control bits for power management.
• Bits [7:4]: Reserved
These bits are unused in the ATmega48A/48PA/88A/88PA/168A/168PA/328/328P, and will
always be read as zero.
• Bits 3:1 – SM[2:0]: Sleep Mode Select Bits 2, 1, and 0
These bits select between the five available sleep modes as shown in
Table 9-2.
Note:
• Bit 0 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s
purpose, it is recommended to write the Sleep Enable (SE) bit to one just before the execution of
the SLEEP instruction and to clear it immediately after waking up.
ATmega48A/48PA/88A/88PA/168A/168PA/328/328
Bit
0x33 (0x53)
Read/Write
Initial Value
SM2
0
0
0
0
1
1
1
1
1. Standby mode is only recommended for use with external crystals or resonators.
Sleep Mode Select
R
7
–
0
SM1
0
0
1
1
0
0
1
1
R
6
–
0
R
5
–
0
SM0
0
1
0
1
0
1
0
1
R
4
–
0
Sleep Mode
Idle
ADC Noise Reduction
Power-down
Power-save
Reserved
Reserved
Standby
External Standby
SM2
R/W
3
0
(1)
SM1
R/W
2
0
(1)
SM0
R/W
Table
1
0
9-2.
R/W
SE
0
0
SMCR
44