ATMEGA32L-8MI Atmel, ATMEGA32L-8MI Datasheet - Page 180
![IC AVR MCU 32K LV 8MHZ IND 44QFN](/photos/12/13/121316/313-44-qfn_sml.jpg)
ATMEGA32L-8MI
Manufacturer Part Number
ATMEGA32L-8MI
Description
IC AVR MCU 32K LV 8MHZ IND 44QFN
Manufacturer
Atmel
Series
AVR® ATmegar
Specifications of ATMEGA32L-8MI
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
32KB (16K x 16)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-VQFN Exposed Pad
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 180 of 346
- Download datasheet (6Mb)
Using the TWI
Figure 85. Interfacing the Application to the TWI in a Typical Transmission
2503Q–AVR–02/11
Application
Hardware
Action
Action
TWI
TWI bus
writes to TWCR
transmission of
1. Application
START condition sent
Status code indicates
to initiate
START
2. TWINT set.
START
• Bit 0 – TWGCE: TWI General Call Recognition Enable Bit
If set, this bit enables the recognition of a General Call given over the Two-wire Serial Bus.
The AVR TWI is byte-oriented and interrupt based. Interrupts are issued after all bus events, like
reception of a byte or transmission of a START condition. Because the TWI is interrupt-based,
the application software is free to carry on other operations during a TWI byte transfer. Note that
the TWI Interrupt Enable (TWIE) bit in TWCR together with the Global Interrupt Enable bit in
SREG allow the application to decide whether or not assertion of the TWINT Flag should gener-
ate an interrupt request. If the TWIE bit is cleared, the application must poll the TWINT Flag in
order to detect actions on the TWI bus.
When the TWINT Flag is asserted, the TWI has finished an operation and awaits application
response. In this case, the TWI Status Register (TWSR) contains a value indicating the current
state of the TWI bus. The application software can then decide how the TWI should behave in
the next TWI bus cycle by manipulating the TWCR and TWDR Registers.
Figure 85
example, a master wishes to transmit a single data byte to a slave. This description is quite
abstract, a more detailed explanation follows later in this section. A simple code example imple-
menting the desired behaviour is also presented.
1. The first step in a TWI transmission is to transmit a START condition. This is done by
2. When the START condition has been transmitted, the TWINT Flag in TWCR is set, and
3. The application software should now examine the value of TWSR, to make sure that the
TWDR, and loads appropriate control
3. Check TWSR to see if START was
signals into TWCR, making sure that
TWINT is written to one, and TWSTA
sendt. Application loads SLA+W into
writing a specific value into TWCR, instructing the TWI hardware to transmit a START
condition. Which value to write is described later on. However, it is important that the
TWINT bit is set in the value written. Writing a one to TWINT clears the Flag. The TWI
will not start any operation as long as the TWINT bit in TWCR is set. Immediately after
the application has cleared TWINT, the TWI will initiate transmission of the START
condition.
TWSR is updated with a status code indicating that the START condition has success-
fully been sent.
START condition was successfully transmitted. If TWSR indicates otherwise, the applica-
tion software might take some special action, like calling an error routine. Assuming that
the status code is as expected, the application must load SLA+W into TWDR. Remember
is written to zero
is a simple example of how the application can interface to the TWI hardware. In this
SLA+W
Status code indicates
SLA+W sent, ACK
4. TWINT set.
received
A
Application loads data into TWDR, and
5. Check TWSR to see if SLA+W was
loads appropriate control signals into
TWCR, making sure that TWINT is
sent and ACK received.
written to one
Data
data sent, ACK received
Status code indicates
6. TWINT set.
A
making sure that TWINT is written to one
7. Check TWSR to see if data was sent
Application loads appropriate control
signals to send STOP into TWCR,
STOP
ATmega32(L)
and ACK received.
TWINT set
Indicates
180
Related parts for ATMEGA32L-8MI
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATmega32](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATMEGA32-8AU](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
![ATMEGA32-16MU](/photos/12/13/121316/313-44-qfn_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ 5V 44-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16PU](/photos/6/70/67049/453-40-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ 5V 40DIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16AU](/photos/6/70/67042/313-44-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ 5V 44TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16PI](/photos/6/70/67049/453-40-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ IND 40-DIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16AI](/photos/6/70/67042/313-44-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ IND 44-TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16AUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 32KB FLASH 16MHZ 44TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16MUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 32KB FLASH 16MHZ 44QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16AQ](/photos/6/70/67042/313-44-tqfp_tmb.jpg)
Part Number:
Description:
MCU AVR 32K FLASH 16MHZ 44-TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16PC](/photos/6/70/67049/453-40-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ COM 40-DIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16MC](/photos/12/13/121316/313-44-qfn_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ COM 44-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA32-16AC](/photos/6/70/67042/313-44-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 16MHZ COM 44-TQFP
Manufacturer:
Atmel
Datasheet: