ATTINY12V-1PC Atmel, ATTINY12V-1PC Datasheet - Page 48
![IC AVR MCU 1MHZ 1.8V 8DIP](/photos/6/50/65033/313-8-dip_sml.jpg)
ATTINY12V-1PC
Manufacturer Part Number
ATTINY12V-1PC
Description
IC AVR MCU 1MHZ 1.8V 8DIP
Manufacturer
Atmel
Series
AVR® ATtinyr
Specifications of ATTINY12V-1PC
Core Processor
AVR
Core Size
8-Bit
Speed
1.2MHz
Peripherals
POR, WDT
Number Of I /o
6
Program Memory Size
1KB (512 x 16)
Program Memory Type
FLASH
Eeprom Size
64 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
0°C ~ 70°C
Package / Case
8-DIP (0.300", 7.62mm)
Data Bus Width
8 bit
Maximum Clock Frequency
8 MHz
Number Of Programmable I/os
6
Number Of Timers
1
Operating Supply Voltage
1.8 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
Minimum Operating Temperature
- 55 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Ram Size
-
Data Converters
-
Connectivity
-
Lead Free Status / Rohs Status
No
Other names
ATTINY12V1PC
Memory
Programming
Program (and Data)
Memory Lock Bits
Fuse Bits in ATtiny11
Fuse Bits in ATtiny12
48
ATtiny11/12
The ATtiny11/12 MCU provides two lock bits which can be left unprogrammed (“1”) or
can be programmed (“0”) to obtain the additional features listed in Table 21. The lock
bits can only be erased with the Chip Erase command
Table 21. Lock Bit Protection Modes
Note:
The ATtiny11 has five fuse bits, FSTRT, RSTDISBL and CKSEL2..0.
•
•
•
The status of the fuse bits is not affected by Chip Erase.
Note:
The ATtiny12 has eight fuse bits, BODLEVEL, BODEN, SPIEN, RSTDISBL and
CKSEL3..0. All the fuse bits are programmable in both High-voltage and Low-voltage
Serial programming modes. Changing the fuses does not have any effect while in pro-
gramming mode.
•
•
•
•
Mode
Memory Lock Bits
1
2
3
FSTRT: See Table 8, “Start-up Times for the ATtiny11 (V
which value to use. Default value is unprogrammed (“1”).
When RSTDISBL is programmed (“0”), the external reset function of pin PB5 is
disabled.
CKSEL2..0: See Table 3, “Device Clocking Options Select,” on page 10, for which
combination of CKSEL2..0 to use. Default value is “100”, internal RC oscillator.
The BODLEVEL Fuse selects the Brown-out Detection level and changes the start-
up times. See “Brown-out Detection (ATtiny12)” on page 27. See Table 10,
“ATtiny12 Clock Options and Start-up Times,” on page 25. Default value is
programmed (“0”).
When the BODEN Fuse is programmed (“0”), the Brown-out Detector is enabled.
See “Brown-out Detection (ATtiny12)” on page 27. Default value is unprogrammed
(“1”).
When the SPIEN Fuse bit is programmed (“0”), Low-Voltage Serial Program and
Data Downloading is enabled. Default value is programmed (“0”). Unprogramming
this fuse while in the Low-Voltage Serial Programming mode will disable future in-
system downloading attempts.
When the RSTDISBL Fuse is programmed (“0”), the external reset function of pin
PB5 is disabled.
while in the Low-Voltage Serial Programming mode will disable future in-system
downloading attempts.
1. In the High-voltage Serial Programming mode, further programming of the fuse bits
1. If the RSTDISBL Fuse is programmed, then the programming hardware should apply
LB1
1
0
0
are also disabled. Program the fuse bits before programming the lock bits.
+12V to PB5 while the ATtiny11 is in Power-on Reset. If not, the part can fail to enter
programming mode caused by drive contention on PB0.
(1)
Default value is unprogrammed (“1”).
LB2
1
1
0
(1)
Protection Type
No memory lock features enabled.
Further programming of the Flash (and EEPROM for ATtiny12) is
disabled.
Same as mode 2, and verify is also disabled.
Default value is unprogrammed (“1”). Programming this fuse
(1)
.
CC
= 2.7V),” on page 23 for
1006F–AVR–06/07