SAK-XC2336B-40F20L AA Infineon Technologies, SAK-XC2336B-40F20L AA Datasheet - Page 67
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
SAK-XC2336B-40F20L AA
Manufacturer Part Number
SAK-XC2336B-40F20L AA
Description
IC MCU 16BIT 320KB FLASH 64LQFP
Manufacturer
Infineon Technologies
Series
XC23xxBr
Datasheet
1.SAK-XC2336B-40F20L_AA.pdf
(107 pages)
Specifications of SAK-XC2336B-40F20L AA
Core Processor
C166SV2
Core Size
16/32-Bit
Speed
20MHz
Connectivity
CAN, EBI/EMI, I²C, LIN, SPI, SSC, UART/USART, USI
Peripherals
I²S, POR, PWM, WDT
Number Of I /o
38
Program Memory Size
320KB (320K x 8)
Program Memory Type
FLASH
Ram Size
34K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 9x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
64-LFQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Table 17
Parameter
Output High voltage
Output Low Voltage
1) Because each double bond pin is connected to two pads (standard pad and high-speed pad), it has twice the
2) Not subject to production test - verified by design/characterization. Hysteresis is implemented to avoid
3) If the input voltage exceeds the respective supply voltage due to ground bouncing (
4) The given values are worst-case values. In production test, this leakage current is only tested at 125 °C; other
5) Drive the indicated minimum current through this pin to change the default pin level driven by the enabled pull
6) Limit the current through this pin to the indicated value so that the enabled pull device can keep the default
7) The maximum deliverable output current of a port driver depends on the selected output driver mode. This
8) As a rule, with decreasing output current the output levels approach the respective supply level (
Data Sheet
normal value. For a list of affected pins refer to the pin definitions table in chapter 2.
metastable states and switching due to internal ground bounce. It cannot suppress switching due to external
system noise under all conditions.
(
leakage current. An additional error current (
Please refer to the definition of the overload coupling factor
values are ensured by correlation. For derating, please refer to the following descriptions: Leakage derating
depending on temperature (
a temperature of 95 °C the resulting leakage current is 3.2 μA. Leakage derating depending on voltage level
(DV =
which applies for maximum temperature.
device:
pin level:
specification is not valid for outputs which are switched to open drain mode. In this case the respective output
will float and the voltage is determined by the external circuit.
V
V
OH
IN
->
>
V
V
V
DDP
V
DDP
DDP
PIN
V
). However, only the levels for nominal output currents are verified.
PIN
), a certain amount of current may flow through the protection diodes. This current adds to the
-
<=
V
>=
DC Characteristics for Lower Voltage Range (cont’d)
PIN
V
IL
V
[V]):
IH
for a pullup;
for a pullup;
7)
7)
I
OZ
=
T
J
I
OZtempmax
= junction temperature [°C]):
V
Symbol
V
V
PIN
V
OH
OL
PIN
>=
CC
CC
<=
- (1.6 x DV) (μA]. This voltage derating formula is an approximation
V
IH
V
IL
for a pulldown.
I
INJ
for a pulldown.
Min.
V
1.0
V
0.4
−
−
DDP
DDP
) will flow if an overload current flows through an adjacent pin.
67
-
-
Values
Typ.
−
−
−
−
K
I
OZ
OV
= 0.05 x e
.
XC2000 Family / Value Line
Max.
−
−
0.4
1.0
(1.5 + 0.028 x TJ>)
Unit Note /
V
V
V
V
Electrical Parameters
V
IN
<
Test Condition
I
I
I
I
[μA]. For example, at
OH
OH
OL
OL
V
SS
≤
≤
≥
≥
) or supply ripple
V1.2, 2010-04
I
I
I
I
OLnom
OLmax
XC2336B
OHmax
OHnom
V
OL
8)
8)
->
V
SS
,