SAF-XC886CLM-8FFI 5V AC Infineon Technologies, SAF-XC886CLM-8FFI 5V AC Datasheet - Page 109

• Manufacturer Part Number: SAF-XC886CLM-8FFI 5V AC
• Description: IC MCU 8BIT FLASH TQFP-48
• Manufacturer: Infineon Technologies
• Series: XC8xxr

Specifications of SAF-XC886CLM-8FFI 5V AC

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-TFQFP
• Core Processor: XC800
• Core Size: 8-Bit
• Speed: 103.2MHz
• Connectivity: CAN, LIN, SSI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 34
• Ram Size: 1.75K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Data Bus Width: 8 bit
• Data Ram Size: 1.75 KB
• Interface Type: JTAG/SPI/SSC/UART
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 4
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: MCBXC88X - BOARD EVAL FOR INFINEON XC88X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: FX886CLM8FFI5VACXT; SAF-XC886CLM-8FFI AB; SAF-XC886CLM-8FFI AB; SAFXC886CLM8FFIABT; SP000217341

3.22
The On-Chip Debug Support (OCDS) provides the basic functionality required for the
software development and debugging of XC800-based systems.
The OCDS design is based on these principles:
•
•
•
•
Features
•
•
•
•
•
The OCDS functional blocks are shown in
block at the center of OCDS system brings together control signals and supports the
overall functionality. The MMC communicates with the XC800 Core, primarily via the
Debug Interface, and also receives reset and clock signals.
After processing memory address and control signals from the core, the MMC provides
proper access to the dedicated extra-memories: a Monitor ROM (holding the code) and
a Monitor RAM (for work-data and Monitor-stack).
The OCDS system is accessed through the JTAG
exclusively for testing and debugging activities and is not normally used in an
application. The dedicated MBC pin is used for external configuration and debugging
control.
Note: All the debug functionality described here can normally be used only after
1) The pins of the JTAG port can be assigned to either the primary port (Port 0) or either of the secondary ports
Data Sheet
(Ports 1 and 2/Port 5).
User must set the JTAG pins (TCK and TDI) as input during connection with the OCDS system.
Use the built-in debug functionality of the XC800 Core
Add a minimum of hardware overhead
Provide support for most of the operations by a Monitor Program
Use standard interfaces to communicate with the Host (a Debugger)
Set breakpoints on instruction address and on address range within the Program
Memory
Set breakpoints on internal RAM address range
Support unlimited software breakpoints in Flash/RAM code region
Process external breaks via JTAG and upon activating a dedicated pin
Step through the program code
XC886/888 has been started in OCDS mode.
On-Chip Debug Support
102
Figure
37. The Monitor Mode Control (MMC)
1)
, which is an interface dedicated
Functional Description
XC886/888CLM
V1.2, 2009-07