HD6473937W Renesas Electronics America, HD6473937W Datasheet - Page 359
HD6473937W
Manufacturer Part Number
HD6473937W
Description
MCU FLASH OTP 60K 100-TQFP
Manufacturer
Renesas Electronics America
Series
H8® H8/300L SLPr
Datasheet
1.HD6473937RXV.pdf
(523 pages)
Specifications of HD6473937W
Core Processor
H8/300L
Core Size
8-Bit
Speed
10MHz
Connectivity
SCI
Peripherals
POR, WDT
Number Of I /o
59
Program Memory Size
60KB (60K x 8)
Program Memory Type
OTP
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-TQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HD6473937W
Manufacturer:
Renesas Electronics America
Quantity:
10 000
- Current page: 359 of 523
- Download datasheet (3Mb)
MTC: Minute Timer Clear. Setting this bit will cause the one minute timer to restart from 0.
EAE: End of Addresses Enable. When this bit is set, the EA bit in the Status Packet will be set
immediately after the FLEX decoder decodes the last address word in the frame if any of the
enabled FLEX decoder addresses was detected in the frame. When this bit is cleared, the EA bit
will never be set.
ON: Turn On Decoder. Set if the FLEX decoder should be decoding FLEX signals. Clear if signal
processing should be off (very low power mode). If the ON bit is changed twice and the control
packets making the changes are received within 2ms of each other, the FLEX decoder may ignore
the double change and stay in its original state (e.g. if it is turned off then on again within 2ms it
may stay on and ignore the off pulse). Therefore it is recommended that the host insures a
minimum of 2ms between changes in the ON bit. (value after reset=0)
Note: Turning off the FLEX decoder must be done using the following sequence. This sequence
Timing between these steps is specified below and is measured from the positive edge of the last
clock of one packet to the positive edge of the last clock of the next packet:
12.3.4
The All Frame Mode Packet is used to decrement temporary address enable counters by one,
decrement the all frame mode counter by one, and/or enable or disable forcing all frame mode. All
frame mode is enabled if any temporary address enable counter is non-zero, the all frame mode
counter is non-zero, or the force all frame mode bit is set. If all frame mode is enabled, the FLEX
decoder will attempt to decode every frame and send a Status Packet with the EOF (end-of-frame)
bit set at the end of every frame. Both the all frame mode counter and the temporary address
enable counters can only be incremented internally by the FLEX decoder and can only be
decremented by the host. The FLEX decoder will increment a temporary address enable counter
whenever a short instruction vector is received assigning the corresponding temporary address.
The minimum time between steps 1 and 2 is 2ms or the programmed shut down time,
whichever is greater. The programmed shut down time is the sum of all the of the times
programmed in the used Receiver Shut Down Settings Packets.
There is no maximum time between steps 1 and 2.
The minimum time between steps 2 and 3 is 2ms.
The maximum time between steps 2 and 3 is the programmed warm up time minus 2ms.
The programmed warm up time is the sum of all the of the times programmed in the used
Receiver Warm Up Settings Packets.
is performed automatically by the FLEXstack software version 1.2 and greater.
3. Turn off the FLEX decoder by sending a Control Packer with the ON bit cleared.
1. Turn off the FLEX decoder by sending a Control Packer with the ON bit cleared.
2. Turn on the FLEX decoder by sending a Control Packer with the ON bit set.
All Frame Mode Packet
345
Related parts for HD6473937W
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
(HD64 Series) Hitachi Single-Chip Microcomputer
Manufacturer:
Hitachi Semiconductor
Datasheet:
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet: