C8051F042-GQR Silicon Laboratories Inc, C8051F042-GQR Datasheet - Page 91

• Manufacturer Part Number: C8051F042-GQR
• Description: IC 8051 MCU 64K FLASH 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F04xr

Specifications of C8051F042-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 64
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x8b, 13x10b; D/A 2x10b, 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• For Use With: 336-1205 - DEV KIT FOR F040/F041/F042/F043
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

7.
The ADC2 subsystem for the C8051F040/1/2/3 consists of an 8-channel, configurable analog multiplexer,
a programmable gain amplifier, and a 500 ksps, 8-bit successive-approximation-register ADC with inte-
grated track-and-hold (see block diagram in Figure 7.1). The AMUX2, PGA2, and Data Conversion Modes,
are all configurable under software control via the Special Function Registers shown in Figure 7.1. The
ADC2 subsystem (8-bit ADC, track-and-hold and PGA) is enabled only when the AD2EN bit in the ADC2
Control register (ADC2CN) is set to logic 1. The ADC2 subsystem is in low power shutdown when this bit is
logic 0. The voltage reference used by ADC2 is selected as described in
(C8051F040/2/4/6)” on page 113
(C8051F041/3/5/7)” on page 117
7.1.
Eight ADC2 channels are available for measurement, as selected by the AMX2SL register (see SFR Defi-
nition 7.2). The PGA amplifies the ADC2 output signal by an amount determined by the states of the
AMP2GN2-0 bits in the ADC2 Configuration register, ADC2CF (SFR Definition 7.1). The PGA can be soft-
ware-programmed for gains of 0.5, 1, 2, or 4. Gain defaults to 0.5 on reset.
Important Note: AIN2 pins also function as Port 1 I/O pins, and must be configured as analog inputs when
used as ADC2 inputs. To configure an AIN2 pin for analog input, set to ‘0’ the corresponding bit in register
P1MDIN. Port 1 pins selected as analog inputs are skipped by the Digital I/O Crossbar. See
“17.1.5. Configuring Port 1, 2, and 3 Pins as Analog Inputs” on page 207
figuring the AIN2 pins.
AIN2.0 (P1.0)
AIN2.1 (P1.1)
AIN2.2 (P1.2)
AIN2.3 (P1.3)
AIN2.4 (P1.4)
AIN2.5 (P1.5)
AIN2.6 (P1.6)
AIN2.7 (P1.7)
8-Bit ADC (ADC2, C8051F040/1/2/3 Only)
Analog Multiplexer and PGA
AMX2CF
Figure 7.1. ADC2 Functional Block Diagram
+
+
+
+
-
-
-
-
AMUX
8-to-1
for C8051F041/3 devices.
AMX2SL
for C8051F040/2 devices, or
X
+
-
AV+
AD2EN
ADC2GTH
AGND
Rev. 1.5
ADC2CF
C8051F040/1/2/3/4/5/6/7
ADC
8-Bit
SAR
AV+
ADC2CN
ADC2LTH
Section “10. Voltage Reference
Start Conversion
Section “9. Voltage Reference
8
for more information on con-
000
001
010
011
1xx
16
Write to AD2BUSY
Timer 3 Overflow
CNVSTR
Timer 2 Overflow
Write to AD0BUSY
(synchronized with
ADC0)
Comp
Dig
ADC Window
Interrupt
Section
91