MC908GZ16MFAE Freescale Semiconductor, MC908GZ16MFAE Datasheet - Page 173

• Manufacturer Part Number: MC908GZ16MFAE
• Description: IC MCU 16K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GZ16MFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: CAN, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GZ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: ESCI, SPI, UART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

After every instruction, the CPU checks all pending interrupts if the I bit is not set. If more than one
interrupt is pending when an instruction is done, the highest priority interrupt is serviced first. In the
example shown in
pending interrupt is serviced before the LDA instruction is executed.
The LDA opcode is prefetched by both the INT1 and INT2 RTI instructions. However, in the case of the
INT1 RTI prefetch, this is a redundant operation.
See
14.3.2 Sources
The sources in
14.3.2.1 Software Interrupt (SWI) Instruction
The software interrupt (SWI) instruction causes a non-maskable interrupt.
14.3.2.2 Break Interrupt
The break module causes the CPU to execute an SWI instruction at a software-programmable break
point.
Freescale Semiconductor
Figure 14-5
To maintain compatibility with the M6805 Family, the H register is not
pushed on the stack during interrupt entry. If the interrupt service routine
modifies the H register or uses the indexed addressing mode, save the H
register and then restore it prior to exiting the routine.
A software interrupt pushes PC onto the stack. An SWI does not push
PC – 1, as a hardware interrupt does.
Table 14-1
for a flowchart depicting interrupt processing.
Figure
14-4, if an interrupt is pending upon exit from the interrupt service routine, the
INT1
INT2
can generate CPU interrupt requests.
MC68HC908GZ16 • MC68HC908GZ8 Data Sheet, Rev. 4
Figure 14-4
CLI
LDA
PSHH
PULH
RTI
PSHH
PULH
RTI
#$FF
.
Interrupt Recognition Example
NOTE
NOTE
INT1 INTERRUPT SERVICE ROUTINE
INT2 INTERRUPT SERVICE ROUTINE
BACKGROUND
ROUTINE
Interrupts
173