C8051F352-GQR Silicon Laboratories Inc, C8051F352-GQR Datasheet - Page 153

• Manufacturer Part Number: C8051F352-GQR
• Description: IC 8051 MCU 8K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F35xr

Specifications of C8051F352-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x16b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Core: 8051
• Processor Series: C8051F3x
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 50 MHz
• Data Ram Size: 768 B
• Data Rom Size: 128 B
• On-chip Adc: Yes
• Number Of Programmable I/os: 17
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.7 V to 3.6 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 16 bit
• A/d Channels Available: 8
• Height: 1.4 mm
• Interface Type: I2C, SMBus, SPI, UART
• Length: 7 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 7 mm
• For Use With: 336-1083 - DEV KIT FOR F350/351/352/353
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

The direction bit (R/W) occupies the least-significant bit position of the address byte. The direction bit is set
to logic 1 to indicate a "READ" operation and cleared to logic 0 to indicate a "WRITE" operation.
All transactions are initiated by a master, with one or more addressed slave devices as the target. The
master generates the START condition and then transmits the slave address and direction bit. If the trans-
action is a WRITE operation from the master to the slave, the master transmits the data a byte at a time
waiting for an ACK from the slave at the end of each byte. For READ operations, the slave transmits the
data waiting for an ACK from the master at the end of each byte. At the end of the data transfer, the master
generates a STOP condition to terminate the transaction and free the bus. Figure 19.3 illustrates a typical
SMBus transaction.
19.3.1. Arbitration
A master may start a transfer only if the bus is free. The bus is free after a STOP condition or after the SCL
and SDA lines remain high for a specified time (see Section “19.3.4. SCL High (SMBus Free) Timeout’ on
page 154). In the event that two or more devices attempt to begin a transfer at the same time, an arbitra-
tion scheme is employed to force one master to give up the bus. The master devices continue transmitting
until one attempts a HIGH while the other transmits a LOW. Since the bus is open-drain, the bus will be
pulled LOW. The master attempting the HIGH will detect a LOW SDA and lose the arbitration. The winning
master continues its transmission without interruption; the losing master becomes a slave and receives the
rest of the transfer if addressed. This arbitration scheme is non-destructive: one device always wins, and
no data is lost.
SCL
SDA
START
SLA6
Slave Address + R/W
Figure 19.3. SMBus Transaction
SLA5-0
R/W
Rev. 1.1
ACK
D7
Data Byte
C8051F350/1/2/3
D6-0
NACK
STOP
153