MC9S08AC60CFGE Freescale Semiconductor, MC9S08AC60CFGE Datasheet - Page 74

• Manufacturer Part Number: MC9S08AC60CFGE
• Description: IC MCU 8BIT 60K FLASH 44-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08AC60CFGE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-LQFP
• Processor Series: S08AC
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 56
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08AC60E, DEMOACEX, DEMOACKIT, DCF51AC256, DC9S08AC128, DC9S08AC16, DC9S08AC60, DEMO51AC256KIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 44LQFP
• Family Name: HCS08
• Maximum Speed: 40 MHz
• For Use With: DEMO9S08AC60E - BOARD DEMO FOR MC9S08A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

1
Chapter 5 Resets, Interrupts, and System Configuration
5.9.2
This register includes read-only status flags to indicate the source of the most recent reset. When a debug
host forces reset by writing 1 to BDFR in the SBDFR register, none of the status bits in SRS will be set.
Writing any value to this register address clears the COP watchdog timer without affecting the contents of
this register. The reset state of these bits depends on what caused the MCU to reset.
74
Any other
Any of these reset sources that are active at the time of reset will cause the corresponding bit(s) to be set; bits corresponding
to sources that are not active at the time of reset will be cleared.
reset:
POR
LVR:
Field
ILOP
POR
COP
PIN
7
6
5
4
W
R
U = Unaffected by reset
System Reset Status Register (SRS)
POR
Power-On Reset — Reset was caused by the power-on detection logic. Because the internal supply voltage was
ramping up at the time, the low-voltage reset (LVR) status bit is also set to indicate that the reset occurred while
the internal supply was below the LVR threshold.
0 Reset not caused by POR.
1 POR caused reset.
External Reset Pin — Reset was caused by an active-low level on the external reset pin.
0 Reset not caused by external reset pin.
1 Reset came from external reset pin.
Computer Operating Properly (COP) Watchdog — Reset was caused by the COP watchdog timer timing out.
This reset source may be blocked by COPE = 0.
0 Reset not caused by COP timeout.
1 Reset caused by COP timeout.
Illegal Opcode — Reset was caused by an attempt to execute an unimplemented or illegal opcode. The STOP
instruction is considered illegal if stop is disabled by STOPE = 0 in the SOPT register. The BGND instruction is
considered illegal if active background mode is disabled by ENBDM = 0 in the BDCSC register.
0 Reset not caused by an illegal opcode.
1 Reset caused by an illegal opcode.
U
1
0
7
PIN
(1)
0
0
6
Writing any value to SIMRS address clears COP watchdog timer.
Table 5-4. SRS Register Field Descriptions
Figure 5-3. System Reset Status (SRS)
MC9S08AC60 Series Data Sheet, Rev. 2
COP
(1)
0
0
5
ILOP
(1)
0
0
4
Description
Reserved
3
0
0
0
ICG
(1)
0
0
2
Freescale Semiconductor
LVD
1
1
0
1
0
0
0
0
0