MC9S08SL16CTL Freescale Semiconductor, MC9S08SL16CTL Datasheet - Page 222

• Manufacturer Part Number: MC9S08SL16CTL
• Description: MCU 16KB FLASH SLIC 28TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08SL16CTL

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-TSSOP
• Processor Series: S08SL
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 6
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08EL32, DEMO9S08EL32AUTO
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Package: 28TSSOP
• Family Name: HCS08
• Maximum Speed: 40 MHz
• For Use With: DEMO9S08EL32 - BOARD DEMO FOR 9S08 EL MCUDEMO9S08EL32AUTO - DEMO BOARD EL32 AUTO
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.6.16 Byte Transfer Mode Operation
This subsection describes the operation and limitations of the optional UART-like byte transfer mode
(BTM). This mode allows sending and receiving individual bytes, but changes the behavior of the SLCBT
registers (now read/write registers) and locks the SLCDLC to 1 byte data length. The SLCBT value now
becomes the bit time reference for the SLIC, where the software sets the length of one bit time rather than
the SLIC module itself. This is similar to an input capture/output compare (IC/OC) count in a timer
module, where the count value represents the number of SLIC clock counts in one bit time.
Byte transfer mode assumes that the user has a very stable, precise oscillator, resonator, or clock reference
input into the MCU and is therefore not appropriate for use with internal oscillators. There is no
synchronization method available to the user in this mode and the user must tell the SLIC how many clock
counts comprise a bit time.
to determine the SLCBT value for different settings.
In the example in
automatically revert to 0x14, resulting in transmitted bit times that are 1.33 SLIC clock periods too short
rather than 0.667 SLIC clock periods too long. The optimal choice, which gives the smallest resolution
error, is the closest even number of SLIC clocks to the exact calculated SLCBT value.
There is a trade-off between maximum bit rate and resolution with the SLIC in BTM mode. Faster SLIC
clock speeds improve resolution, but require higher numbers to be written to the SLCBT registers for a
given desired bit rate. It is up to the user to determine what level of resolution is acceptable for the given
application.
224
It is possible to use the LIN autobauding circuitry in a non-LIN system to
derive the correct bit timing values if system constraints allow. To do this
the SLIC module must be activated in LIN mode (BTM=0) and receive a
break symbol, 0x55 data byte and one additional data byte (at the desired
BTM speed). Upon receiving this sequence of symbols which appears to be
a LIN header, the SLIC module will assert an ID received successfully
interrupt (SLCSV=0x2C). The value in the SLCBT registers will reflect the
bit rate which the 0x55 data character was received and can be saved to
RAM. The user then switches the SLIC into BTM mode and reloads this
value from RAM and the SLIC will be configured to communicate in BTM
mode at the baud rate which the 0x55 data character was sent. Care must be
taken to ensure that any change between LIN and BTM modes be done at
known states in message traffic, such as between message frames, after an
ID is successfully received in LIN mode, or when the LIN bus is IDLE as
indicated by the SLCACT bit equal to 0.
Do not set the SLCBT registers to a value lower than 16 clock counts for
correct operation.
Figure
MC9S08EL32 Series and MC9S08SL16 Series Data Sheet, Rev. 3
12-17, the user should write 0x16, as a write of 0x15 (decimal value of 21) would
Figure
12-17,
Figure
12-18,
NOTE
NOTE
Figure
12-19, and
Figure 12-20
Freescale Semiconductor
show calculations