MC908QY2ACDWE Freescale Semiconductor, MC908QY2ACDWE Datasheet - Page 123

• Manufacturer Part Number: MC908QY2ACDWE
• Description: IC MCU 8BIT 1.5K FLASH 16SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QY2ACDWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 1.5KB (1.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Processor Series: HC08QY
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

POR — Power-On Reset Bit
PIN — External Reset Bit
COP — Computer Operating Properly Reset Bit
ILOP — Illegal Opcode Reset Bit
ILAD — Illegal Address Reset Bit (illegal attempt to fetch an opcode from an unimplemented
address)
MODRST — Monitor Mode Entry Module Reset bit
LVI — Low Voltage Inhibit Reset bit
13.8.2 Break Flag Control Register
The break control register (BFCR) contains a bit that enables software to clear status bits while the MCU
is in a break state.
BCFE — Break Clear Flag Enable Bit
Freescale Semiconductor
This read/write bit enables software to clear status bits by accessing status registers while the MCU is
in a break state. To clear status bits during the break state, the BCFE bit must be set.
1 = Last reset caused by POR circuit
0 = Read of SRSR
1 = Last reset caused by external reset pin (RST)
0 = POR or read of SRSR
1 = Last reset caused by COP counter
0 = POR or read of SRSR
1 = Last reset caused by an illegal opcode
0 = POR or read of SRSR
1 = Last reset caused by an opcode fetch from an illegal address
0 = POR or read of SRSR
1 = Last reset caused by monitor mode entry when vector locations $FFFE and $FFFF are $FF after
0 = POR or read of SRSR
1 = Last reset caused by LVI circuit
0 = POR or read of SRSR
1 = Status bits clearable during break
0 = Status bits not clearable during break
POR while IRQ ≠ V
Reset:
Read:
Write:
BCFE
Bit 7
R
0
Figure 13-20. Break Flag Control Register (BFCR)
= Reserved
TST
MC68HC908QYA/QTA Family Data Sheet, Rev. 3
R
6
R
5
R
4
R
3
R
2
R
1
Bit 0
R
SIM Registers
123