CY8CLED16P01-28PVXI Cypress Semiconductor Corp, CY8CLED16P01-28PVXI Datasheet - Page 37

• Manufacturer Part Number: CY8CLED16P01-28PVXI
• Description: IC PLC PSOC CMOS LED 16CH 28SSOP
• Manufacturer: Cypress Semiconductor Corp
• Series: PowerPSoC® CY8CLEDr

Specifications of CY8CLED16P01-28PVXI

• Package / Case: 28-SSOP
• Core Processor: M8C
• Core Size: 8-Bit
• Speed: 24MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: LED, PLC, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.75 V ~ 5.25 V
• Data Converters: A/D 4x14b; D/A 4x9b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Low Level Output Current: 25 mA
• High Level Output Current: 10 mA
• Operating Supply Voltage: 5 V
• Maximum Supply Current: 14 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (max): 5.25V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Package Type: SSOP
• Mounting: Surface Mount
• Pin Count: 28
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1000 - ISP 4PORT FOR CYPRESS PSOC MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Table 10-20. AC Programming Specifications (continued)
10.4.9 AC I
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40 ° C ≤ T
Table 10-21. AC Characteristics of the I
Document Number: 001-49263 Rev. *E
T
T
T
T
F
T
T
T
T
T
T
T
T
T
Notes
9. For the full industrial range, the user must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing.
10. A Fast-Mode I2C-bus device can be used in a Standard-Mode I2C-bus system, but the requirement t
DSCLK
ERASEALL
PROGRAM_HOT
PROGRAM_COLD
SCLI2C
HDSTAI2C
LOWI2C
HIGHI2C
SUSTAI2C
HDDATI2C
SUDATI2C
SUSTOI2C
BUFI2C
SPI2C
SDA
SCL
Symbol
Refer to the Flash APIs Application Note
if the device does not stretch the LOW period of the SCL signal. If this device does stretch the LOW period of the SCL signal, it must output the next data bit to the
SDA line t
Symbol
2
rmax
S
C Specifications
A
Figure 10-9. Definition for Timing for Fast/Standard Mode on the I
≤ 85 ° C. Typical parameters apply to 5V at 25 ° C and are for design guidance only.
+ t
T
SCL Clock Frequency
Hold Time (repeated) START Condition. After
this period, the first clock pulse is generated.
LOW Period of the SCL Clock
HIGH Period of the SCL Clock
Setup Time for a Repeated START Condition
Data Hold Time
Data Setup Time
Setup Time for STOP Condition
Bus Free Time Between a STOP and START
Condition
Pulse Width of spikes are suppressed by the
input filter
HDSTAI2C
SU;DAT
Data Out Delay from Falling Edge of SCLK
Flash Erase Time (Bulk)
Flash Block Erase + Flash Block Write Time
Flash Block Erase + Flash Block Write Time
T
LOWI2C
= 1000 + 250 = 1250 ns (according to the Standard-Mode I2C-bus specification) before the SCL line is relea sed.
T
HDDATI2C
Description
Description
AN2015
T
T
HIGHI2C
SUDATI2C
2
at
C SDA and SCL Pins
http://www.cypress.com
T
SUSTAI2C
Standard Mode
Min
250
4.0
4.7
4.0
4.7
4.0
4.7
0
0
–
for more information.
Sr
Min
–
–
–
–
Max
100
–
–
–
–
–
–
–
–
–
T
HDSTAI2C
Typ
80
–
–
–
100
Min
SU;DAT
0.6
1.3
0.6
0.6
0.6
1.3
Fast Mode
0
0
0
[10]
2
100
200
Max
C Bus Packaging Dimensions
45
≥ 250 ns must then be met. This is automatically the case
–
[9]
[9]
T
Max
SUSTOI2C
400
T
50
–
–
–
–
–
–
–
–
SPI2C
Units
ms
ms
ms
ns
Units
kHz
μs
μs
μs
μs
μs
ns
μs
μs
ns
Erase all Blocks and protection
fields at once
0°C <= Tj <= 100°C
-40°C <= Tj <= 0°C
P
CY8CLED16P01
T
BUFI2C
Notes
Notes
S
Page 37 of 46
[+] Feedback
[+] Feedback