STM32F103RBT7TR STMicroelectronics, STM32F103RBT7TR Datasheet - Page 9

• Manufacturer Part Number: STM32F103RBT7TR
• Description: MCU ARM 32BIT 64KB FLASH 64LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103RBT7TR

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 51
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 64-LQFP
• Processor Series: STM32F103x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 20 KB
• Interface Type: CAN, I2C, SPI, USART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 51
• Number Of Timers: 4
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, KSDK-STM32-PLUS, KSK-STM32-JL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ST-LINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (12 bit, 16 Channel)
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-8418 - BOARD DEMO DGTL PHOTOFRAME STM32497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

STM32F103xx
Clocks and startup
System clock selection is performed on startup, however the internal RC 8 MHz oscillator is
selected as default CPU clock on reset. An external 4-16 MHz clock can be selected and is
monitored for failure. During such a scenario, it is disabled and software interrupt
management follows. Similarly, full interrupt management of the PLL clock entry is available
when necessary (for example with failure of an indirectly used external oscillator).
Several prescalers allow the configuration of the AHB frequency, the High Speed APB
(APB2) and the low Speed APB (APB1) domains. The maximum frequency of the AHB and
the High Speed APB domains is 72 MHz. The maximum allowed frequency of the Low
Speed APB domain is 36 MHz.
Boot modes
At startup, boot pins are used to select one of three boot options:
The boot loader is located in System Memory. It is used to reprogram the Flash memory by
using the USART.
Power supply schemes
Power supply supervisor
The device has an integrated Power On Reset (POR)/Power Down Reset (PDR) circuitry. It
is always active, and ensures proper operation starting from/down to 2 V. The device
remains in reset mode when V
for an external reset circuit.
The device features an embedded programmable voltage detector (PVD) that monitors the
V
when V
interrupt service routine can then generate a warning message and/or put the MCU into a
safe state. The PVD is enabled by software.
Refer to
V
DD
POR/PDR
Boot from User Flash
Boot from System Memory
Boot from SRAM
V
Provided externally through V
V
and PLL. In V
V
registers (through power switch) when V
power supply and compares it to the V
DD
SSA
BAT
DD
Table 9: Embedded reset and power control block characteristics
= 2.0 to 3.6 V: external power supply for I/Os and the internal regulator.
, V
= 1.8 to 3.6 V: power supply for RTC, external clock 32 kHz oscillator and backup
and V
drops below the V
DDA
PVD
= 2.0 to 3.6 V: external analog power supplies for ADC, Reset blocks, RCs
DD
.
range (ADC is limited at 2.4 V).
PVD
DD
is below a specified threshold, V
and/or when V
DD
pins.
PVD
DD
threshold. An interrupt can be generated
DD
is not present.
is higher than the V
POR/PDR
PVD
, without the need
for the values of
threshold. The
Description
9/67