ST7FLITE05Y0B6 STMicroelectronics, ST7FLITE05Y0B6 Datasheet - Page 59

• Manufacturer Part Number: ST7FLITE05Y0B6
• Description: IC MCU 8BIT 1.5K FLASH 16-DIP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITE05Y0B6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 13
• Program Memory Size: 1.5KB (1.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Data Converters: A/D 5x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-DIP (0.300", 7.62mm)
• Processor Series: ST7FLITE0x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 2
• Operating Supply Voltage: 2.4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ST7FLIT0-IND/USB, ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• For Use With: 497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5080 - EVAL BOARD AC/AC CHOPPER DRIVER497-5049 - KIT STARTER RAISONANCE ST7FLITE
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: In Transition

11.3 SERIAL PERIPHERAL INTERFACE (SPI)
11.3.1 Introduction
The Serial Peripheral Interface (SPI) allows full-
duplex, synchronous, serial communication with
external devices. An SPI system may consist of a
master and one or more slaves however the SPI
interface can not be a master in a multi-master
system.
11.3.2 Main Features
■
■
■
■
■
■
■
■
■
Note: In slave mode, continuous transmission is
not possible at maximum frequency due to the
Figure 37. Serial Peripheral Interface Block Diagram
Full duplex synchronous transfers (on 3 lines)
Simplex synchronous transfers (on 2 lines)
Master or slave operation
Six master mode frequencies (f
f
SS Management by software or hardware
Programmable clock polarity and phase
End of transfer interrupt flag
Write collision, Master Mode Fault and Overrun
flags
MOSI
MISO
CPU
SCK
SS
/2 max. slave mode frequency (see note)
SOD
bit
SPIDR
8-Bit Shift Register
Read Buffer
SERIAL CLOCK
CPU
GENERATOR
CONTROL
MASTER
/4 max.)
Data/Address Bus
Read
Write
software overhead for clearing status flags and to
initiate the next transmission sequence.
11.3.3 General Description
Figure 37
(SPI) block diagram. There are 3 registers:
The SPI is connected to external devices through
3 pins:
– SPI Control Register (SPICR)
– SPI Control/Status Register (SPICSR)
– SPI Data Register (SPIDR)
– MISO: Master In / Slave Out data
– MOSI: Master Out / Slave In data
– SCK: Serial Clock out by SPI masters and in-
– SS: Slave select:
put by SPI slaves
This input signal acts as a ‘chip select’ to let
the SPI master communicate with slaves indi-
vidually and to avoid contention on the data
lines. Slave SS inputs can be driven by stand-
ard I/O ports on the master MCU.
7
SPIE
SPIF WCOL
7
SPE
shows the serial peripheral interface
CONTROL
SPR2
ST7LITE0xY0, ST7LITESxY0
OVR
STATE
SPI
Interrupt
request
MODF
MSTR
CPOL
0
CPHA
SOD
SS
SPICR
SPICSR
SSM
SPR1
0
1
SPR0
SSI
0
59/124
0
1