LPC2478FET208,551 NXP Semiconductors, LPC2478FET208,551 Datasheet - Page 5

• Manufacturer Part Number: LPC2478FET208,551
• Description: IC ARM7 MCU 512K LCD 208-TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2478FET208,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 208-TFBGA
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, LCD, POR, PWM, WDT
• Number Of I /o: 160
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2C/I2S/IrDA/SPI/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 160
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, DK-35TS-LPC2478, DK-57TS-LPC2478, DK-57VTS-LPC2478, SOMDIMM-LPC2478, SAB-TFBGA208, KSK-LPC2478-JL, MCB2470
• Development Tools By Supplier: OM11015, OM11019, OM11022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Package: 208TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1034 - PROGRAMMERS, DEVELOPMENT SYSTEMS622-1033 - KIT LCD TOUCH 5.7" FOR LPC2478MCB2470 - BOARD EVAL NXP LPC247X SERIESOM11022 - EVAL LPC-STICK WITH LPC2478OM11019 - BOARD EVAL FOR LPC2478568-4742 - MODULE DIMM LPC2478 ARM7568-4741 - KIT LCD TOUCH 5.7" FOR LPC2478622-1028 - KIT LCD TOUCH 5.7" FOR LPC2478KSDKLPC2478-PL - KIT IAR KICKSTART NXP LPC2478622-1024 - BOARD SCKT ADAPTER FOR TFBGA208568-4369 - BOARD EVAL FOR LPC2478622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4364; 935284072551; LPC2478FET208-S

NXP Semiconductors
ES_LPC2478
Errata sheet
3.2 Core.1: Incorrect update of the Abort Link register in Thumb state
Introduction:
If the processor is in Thumb state and executing the code sequence STR, STMIA or
PUSH followed by a PC relative load, and the STR, STMIA or PUSH is aborted, the PC is
saved to the abort link register.
Problem:
In this situation the PC is saved to the abort link register in word resolution, instead of
half-word resolution.
Conditions:
The processor must be in Thumb state, and the following sequence must occur:
<any instruction>
<STR, STMIA, PUSH> <---- data abort on this instruction
LDR rn, [pc,#offset]
In this case the PC is saved to the link register R14_abt in only word resolution, not
half-word resolution. The effect is that the link register holds an address that could be #2
less than it should be, so any abort handler could return to one instruction earlier than
intended.
Work-around:
In a system that does not use Thumb state, there will be no problem.
In a system that uses Thumb state but does not use data aborts, or does not try to use
data aborts in a recoverable manner, there will be no problem.
Otherwise the workaround is to ensure that a STR, STMIA or PUSH cannot precede a
PC-relative load. One method for this is to add a NOP before any PC-relative load
instruction. However this is would have to be done manually.
All information provided in this document is subject to legal disclaimers.
Rev. 6 — 1 March 2011
ES_LPC2478
Errata sheet LPC2478
© NXP B.V. 2011. All rights reserved.
5 of 10