P89LPC922A1FN,112 NXP Semiconductors, P89LPC922A1FN,112 Datasheet - Page 35

• Manufacturer Part Number: P89LPC922A1FN,112
• Description: IC 80C51 MCU FLASH 8K 20-DIP
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC922A1FN,112

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 20-DIP (0.300", 7.62mm)
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: I²C, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89LPC
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Operating Supply Voltage: 2.4 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 4 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935288636112

NXP Semiconductors
P89LPC92X1
Product data sheet
7.18.3 Total Power-down mode
7.19 Reset
Some chip functions continue to operate and draw power during Power-down mode,
increasing the total power used during power-down. These include: Brownout detect,
watchdog timer, comparators (note that comparators can be powered down separately),
and RTC/system timer. The internal RC oscillator is disabled unless both the RC oscillator
has been selected as the system clock and the RTC is enabled.
This is the same as Power-down mode except that the brownout detection circuitry and
the voltage comparators are also disabled to conserve additional power. The internal RC
oscillator is disabled unless both the RC oscillator has been selected as the system clock
and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during
power-down, there will be high power consumption. Please use an external low frequency
clock to achieve low power with the RTC running during power-down.
The P1.5/RST pin can function as either a LOW-active reset input or as a digital input,
P1.5. The Reset Pin Enable (RPE) bit in UCFG1, when set to logic 1, enables the external
reset input function on P1.5. When cleared, P1.5 may be used as an input pin.
Remark: During a power-up sequence, the RPE selection is overridden and this pin
always functions as a reset input. An external circuit connected to this pin should not
hold this pin LOW during a power-on sequence as this will keep the device in reset.
After power-up this pin will function as defined by the RPE bit. Only a power-up reset will
temporarily override the selection defined by RPE bit. Other sources of reset will not
override the RPE bit.
Note: During a power cycle, V
to ensure a power-on reset (see
Reset can be triggered from the following sources:
For every reset source, there is a flag in the Reset Register, RSTSRC. The user can read
this register to determine the most recent reset source. These flag bits can be cleared in
software by writing a logic 0 to the corresponding bit. More than one flag bit may be set:
•
•
•
•
•
•
•
•
•
External reset pin (during power-up or if user configured via UCFG1)
Power-on detect
Brownout detect
Watchdog timer
Software reset
UART break character detect reset
During a power-on reset, both POF and BOF are set but the other flag bits are
cleared.
A Watchdog reset is similar to a power-on reset, both POF and BOF are set but the
other flag bits are cleared.
For any other reset, previously set flag bits that have not been cleared will remain set.
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 1 December 2010
P89LPC9201/9211/922A1/9241/
DD
Table 12 “Static
must fall below V
characteristics”).
POR
8-bit microcontroller with 8-bit ADC
before power is reapplied, in order
© NXP B.V. 2010. All rights reserved.
35 of 75