DSPIC30F6014-20E/PF Microchip Technology, DSPIC30F6014-20E/PF Datasheet - Page 3

• Manufacturer Part Number: DSPIC30F6014-20E/PF
• Description: IC DSPIC MCU/DSP 144K 80TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F6014-20E/PF

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 144KB (48K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-TQFP, 80-VQFP
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1DM300004-2 - BOARD DEMO DSPICDEM.NET 2DM300004-1 - BOARD DEMO DSPICDEM.NET 1AC164314 - MODULE SKT FOR PM3 80PFAC30F001 - MODULE SOCKET DSPIC30F 80TQFPXLT80PT2 - SOCKET TRANSITION ICE 80TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DSPIC30F601420EPF

TABLE 2:
© 2010 Microchip Technology Inc.
Operations
Note 1:
Controller
Interrupt
Memory
Memory
Module
Sleep
Timer
Flash
Flash
Mode
I
CAN
CPU
PSV
CAN
2
PLL
PLL
PLL
I/O
I
I
I
I
C™
2
2
2
2
C
C
C
C
Only those issues indicated in the last column apply to the current silicon revision.
Bus Collision
RX Filters 3,
Sleep Mode
Slave Mode
I
Multiplexed
Lock Status
Addressing
Addressing
Addressing
Operations
Regulation
DD
Protection
on SFRs
4x Mode
8x Mode
Feature
with IC1
Port Pin
SILICON ISSUE SUMMARY (CONTINUED)
4 and 5
Voltage
10-bit
10-bit
10-bit
Read
Code
Current
—
—
bit
—
Number
Item
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
Read operations performed on CAN module Special Function
Registers (SFRs) may yield incorrect results at operation over
20 MIPS.
This release of silicon exhibits a current draw (I
approximately 370 mA during a Row Erase operation performed
on program Flash memory.
For this release of silicon, applications operating off 5 volts V
30 MIPS should ensure that the V
Addresses in the range 0x6000 through 0xFFFF may not be
code-protected for this revision of dsPIC30F6011 and
dsPIC30F6013 silicon.
The 4x PLL mode of operation may not function correctly for
certain input frequencies.
An interrupt occurring immediately after modifying the CPU IPL,
interrupt IPL, interrupt enable or interrupt flag may cause an
address error trap.
If 8x PLL mode is used, the input frequency range is 5 MHz-10 MHz
instead of 4 MHz-10 MHz.
Execution of the Sleep instruction (PWRSAV #0) may cause
incorrect program operation after the device wakes up from
Sleep. The current consumption during Sleep may also increase
beyond the specifications listed in the device data sheet.
The I
I
The port I/O pin multiplexed with the Input Capture 1 (IC1)
function cannot be used as a digital input pin when the UART
auto-baud feature is enabled.
When the I
the same address bits (A10 and A9) as other I
A10 and A9 bits may not work as expected.
Clock switching prevents the device from waking up from Sleep.
The PLL LOCK Status bit (OSCCON<5>) can occasionally get
cleared and generate an oscillator failure trap even when the
PLL is still locked and functioning correctly.
An address error trap occurs in certain addressing modes when
accessing the first four bytes of any PSV page.
The 10-bit slave does not set the RBF flag or load the I2CxRCV
register, on address match if the Least Significant bits (LSbs) of
the address are the same as the 7-bit reserved addresses.
When the I
address of 0x102, the I2CxRCV register content for the lower
address byte is 0x01 rather than 0x02.
When the I
generates a glitch on the SDA and SCL pins, causing a false
communication start in a single-master configuration or a bus
collision in a multi-master configuration.
CAN Receive filters 3, 4 and 5 may not work for a given
combination of instruction cycle speed and CAN bit time quanta.
2
C slave.
2
C module loses incoming data bytes when operating as an
2
2
2
C module is configured for 10-bit addressing using
C module is configured as a 10-bit slave with an
C module is enabled, the dsPIC
dsPIC30F6011/6012/6013/6014
Issue Summary
DD
remains within 5% of 5 volts.
®
DSC device
2
DD
C devices, the
) of
DD
at
DS80456D-page 3
Revisions
A3 B1 B2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Affected
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
(1)
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X