AT91SAM9G10-CU Atmel, AT91SAM9G10-CU Datasheet - Page 33

• Manufacturer Part Number: AT91SAM9G10-CU
• Description: IC MCU ARM9 SAMPLING 217CBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9G10-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 266MHz
• Connectivity: EBI/EMI, I²C, IrDA, ISI, MMC, SPI, SSC, UART/USART, USB
• Peripherals: DMA, LCD, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: ROM
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 1.32 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Controller Family/series: AT91
• No. Of I/o's: 96
• Ram Memory Size: 16KB
• Cpu Speed: 266MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: EBI, SPI, TWI, USART
• Maximum Clock Frequency: 266 MHz
• Number Of Programmable I/os: 96
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9G10-EK
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

10.7
10.8
10.9
6462AS–ATARM–03-Jun-09
Serial Peripheral Interface
Two-wire Interface
USART
• Supports communication with serial external devices
• Master or slave serial peripheral bus interface
• Very fast transfers supported
• Compatibility with standard two-wire serial memories
• One, two or three bytes for slave address
• Sequential read/write operations
• Supports either master or slave modes
• Master, multi-master and slave mode operation
• Bit rate: up to 400 Kbits
• General call supported in slave mode
• Programmable Baud Rate Generator
• 5- to 9-bit full-duplex synchronous or asynchronous serial communications
– Four chip selects with external decoder support allow communication with up to
– Serial memories, such as DataFlash and 3-wire EEPROMs
– Serial peripherals, such as ADCs, DACs, LCD Controllers, CAN Controllers and
– External co-processors
– 8- to 16-bit programmable data length per chip select
– Programmable phase and polarity per chip select
– Programmable transfer delays between consecutive transfers and between clock
– Programmable delay between consecutive transfers
– Selectable mode fault detection
– Transfers with baud rates up to MCK
– The chip select line may be left active to speed up transfers on the same device
– 1, 1.5 or 2 stop bits in Asynchronous Mode or 1 or 2 stop bits in Synchronous Mode
– Parity generation and error detection
– Framing error detection, overrun error detection
– MSB- or LSB-first
– Optional break generation and detection
– By-8 or by-16 over-sampling receiver frequency
– Hardware handshaking RTS-CTS
– Receiver time-out and transmitter timeguard
– Optional Multi-drop Mode with address generation and detection
– Optional Manchester Encoding
fifteen peripherals
Sensors
and data per chip select
AT91SAM9G10
33