ATMEGA3250P-20AUR Atmel, ATMEGA3250P-20AUR Datasheet - Page 129

• Manufacturer Part Number: ATMEGA3250P-20AUR
• Description: MCU AVR 32K FLASH 20MHZ 100TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA3250P-20AUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8023F–AVR–07/09
Table 15-3
PWM mode.
Table 15-3.
Note:
Table 15-4
correct or the phase and frequency correct, PWM mode.
Table 15-4.
Note:
• Bit 1:0 – WGM11:0: Waveform Generation Mode
Combined with the WGM13:2 bits found in the TCCR1B Register, these bits control the counting
sequence of the counter, the source for maximum (TOP) counter value, and what type of wave-
form generation to be used, see
Timer/Counter unit are: Normal mode (counter), Clear Timer on Compare match (CTC) mode,
and three types of Pulse Width Modulation (PWM) modes. (See
119).
COM1A1/COM1B1
COM1A1/COM1B1
1. A special case occurs when OCR1A/OCR1B equals TOP and COM1A1/COM1B1 is set. In
1. A special case occurs when OCR1A/OCR1B equals TOP and COM1A1/COM1B1 is set.
0
0
1
1
0
0
1
1
this case the compare match is ignored, but the set or clear is done at BOTTOM.
“15.9.3” on page 120.
Section “15.9.4” on page 122.
shows the COM1x1:0 bit functionality when the WGM13:0 bits are set to the phase
shows the COM1x1:0 bit functionality when the WGM13:0 bits are set to the fast
Compare Output Mode, Fast PWM
Compare Output Mode, Phase Correct and Phase and Frequency Correct
PWM
(1)
COM1A0/COM1B0
COM1A0/COM1B0
for more details.
Table 15-14 on page
0
1
0
1
0
1
0
1
for more details.
Description
Normal port operation, OC1A/OC1B disconnected.
WGM13:0 = 14 or 15: Toggle OC1A on Compare
Match, OC1B disconnected (normal port operation).
For all other WGM1 settings, normal port operation,
OC1A/OC1B disconnected.
Clear OC1A/OC1B on Compare Match, set
OC1A/OC1B at BOTTOM (non-inverting mode)
Set OC1A/OC1B on Compare Match, clear
OC1A/OC1B at BOTTOM (inverting mode)
Description
Normal port operation, OC1A/OC1B disconnected.
WGM13:0 = 9 or 11: Toggle OC1A on Compare
Match, OC1B disconnected (normal port operation).
For all other WGM1 settings, normal port operation,
OC1A/OC1B disconnected.
Clear OC1A/OC1B on Compare Match when up-
counting. Set OC1A/OC1B on Compare Match when
counting down.
Set OC1A/OC1B on Compare Match when up-
counting. Clear OC1A/OC1B on Compare Match
when counting down.
(1)
130. Modes of operation supported by the
ATmega325P/3250P
”Modes of Operation” on page
See Section
See
129