ATMEGA165PV-8AUR Atmel, ATMEGA165PV-8AUR Datasheet - Page 272

• Manufacturer Part Number: ATMEGA165PV-8AUR
• Description: MCU AVR 16KB FLASH 8MHZ 64TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA165PV-8AUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, USART, USI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

25.7
25.7.1
25.7.2
25.7.3
8019K–AVR–11/10
Parallel Programming
Enter Programming Mode
Considerations for Efficient Programming
Chip Erase
The following algorithm puts the device in parallel programming mode:
1. Apply 4.5V - 5.5V between V
2. Set RESET to “0” and toggle XTAL1 at least six times.
3. Set the Prog_enable pins listed in
4. Apply 11.5V - 12.5V to RESET. Any activity on Prog_enable pins within 100 ns after
5. Wait at least 50 µs before sending a new command.
The loaded command and address are retained in the device during programming. For efficient
programming, the following should be considered.
• The command needs only be loaded once when writing or reading multiple memory locations.
• Skip writing the data value 0xFF, that is the contents of the entire EEPROM (unless the
• Address high byte needs only be loaded before programming or reading a new 256 word
The Chip Erase will erase the Flash and EEPROM
not reset until the program memory has been completely erased. The Fuse bits are not
changed. A Chip Erase must be performed before the Flash and/or EEPROM are
reprogrammed.
Note:
Load Command “Chip Erase”
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set BS1 to “0”.
3. Set DATA to “1000 0000”. This is the command for Chip Erase.
4. Give XTAL1 a positive pulse. This loads the command.
5. Give WR a negative pulse. This starts the Chip Erase. RDY/BSY goes low.
6. Wait until RDY/BSY goes high before loading a new command.
EESAVE Fuse is programmed) and Flash after a Chip Erase.
window in Flash or 256 byte EEPROM. This consideration also applies to Signature bytes
reading.
100 ns.
+12V has been applied to RESET, will cause the device to fail entering programming
mode.
1. The EEPRPOM memory is preserved during Chip Erase if the EESAVE Fuse is programmed.
CC
and GND.
Table 25-10 on page 270
(1)
memories plus Lock bits. The Lock bits are
to “0000” and wait at least
ATmega165P
272