ATMEGA8L-8PU Atmel, ATMEGA8L-8PU Datasheet - Page 24

• Manufacturer Part Number: ATMEGA8L-8PU
• Description: IC AVR MCU 8K 8MHZ 3V 28DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8L-8PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SPI/TWI/USART
• Total Internal Ram Size: 1KB
• # I/os (max): 23
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 6-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 28
• Package Type: PDIP
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AVR MEGA
• No. Of I/o's: 23
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Changes from Rev.
2486B-12/01 to
Rev. 2486C-03/02
1. Updated TWI Chapter.
2. Updated Description of OSCCAL Calibration Byte.
3. Added Some Preliminary Test Limits and Characterization Data.
4. Updated Programming Figures.
5. Added a Description on how to Enter Parallel Programming Mode if RESET Pin is Dis-
More details regarding use of the TWI Power-down operation and using the TWI as Master
with low TWBRR values are added into the datasheet.
Added the note at the end of the
Added the description at the end of
In the datasheet, it was not explained how to take advantage of the calibration bytes for 2, 4,
and 8 MHz Oscillator selections. This is now added in the following sections:
Improved description of
bration Byte” on page
Removed some of the TBD’s in the following tables and pages:
Table 3 on page
-40°C to +85°C, VCC = 2.7V to 5.5V (unless otherwise noted)” on page
page
Figure 104 on page 219
must be connected during Programming mode.
abled or if External Oscillators are Selected.
Added a note in section
237, and
Table 102 on page
26,
Table 15 on page
218.
“Enter Programming Mode” on page
“Oscillator Calibration Register – OSCCAL” on page 31
and
Figure 112 on page 230
“Bit Rate Generator Unit” on page
239.
“Address Match Unit” on page
38,
Table 16 on page
are updated to also reflect that AV
42,
221.
Table 17 on page
164.
164.
235,
Table 99 on
and
44,
“Cali-
“T
A
CC
=