PIC16C72AT-04/SS Microchip Technology, PIC16C72AT-04/SS Datasheet - Page 49

• Manufacturer Part Number: PIC16C72AT-04/SS
• Description: IC MCU OTP 2KX14 A/D PWM 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C72AT-04/SS

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 4MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x8b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SSOP
• For Use With: 309-1025 - ADAPTER 28-SSOP TO 28-DIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

9.0
The analog-to-digital (A/D) converter module has five
input channels.
The A/D allows conversion of an analog input signal to
a corresponding 8-bit digital number (refer to Applica-
tion Note AN546 for use of A/D Converter). The output
of the sample and hold is the input into the converter,
which generates the result via successive approxima-
tion. The analog reference voltage is software select-
able to either the device’s positive supply voltage (V
or the voltage level on the RA3/AN3/V
The A/D converter has the feature of being able to
operate while the device is in SLEEP mode. To operate
in sleep, the A/D conversion clock must be derived from
the A/D’s internal RC oscillator.
REGISTER 9-1:ADCON0 REGISTER (ADDRESS 1Fh)
Note:
1999 Microchip Technology Inc.
bit7
bit 7-6: ADCS1:ADCS0: A/D Conversion Clock Select bits
bit 5-3: CHS2:CHS0: Analog Channel Select bits
bit 2:
bit 1:
bit 0:
ADCS1 ADCS0
R/W-0
ANALOG-TO-DIGITAL
CONVERTER (A/D) MODULE
This section applies to the PIC16C72A
only.
00 = F
01 = F
10 = F
11 = F
000 = channel 0, (RA0/AN0)
001 = channel 1, (RA1/AN1)
010 = channel 2, (RA2/AN2)
011 = channel 3, (RA3/AN3)
100 = channel 4, (RA5/AN4)
GO/DONE: A/D Conversion Status bit
If ADON = 1
1 = A/D conversion in progress (setting this bit starts the A/D conversion)
0 = A/D conversion not in progress (This bit is automatically cleared by hardware when the A/D
conversion is complete)
Unimplemented: Read as '0'
ADON: A/D On bit
1 = A/D converter module is operating
0 = A/D converter module is shutoff and consumes no operating current
R/W-0
OSC
OSC
OSC
RC
(clock derived from an internal RC oscillator)
/2
/8
/32
R/W-0
CHS2
R/W-0
CHS1
REF
pin.
R/W-0
CHS0
Preliminary
DD
GO/DONE
)
R/W-0
Additional information on the A/D module is available in
the
(DS33023).
The A/D module has three registers. These registers
are:
A device reset forces all registers to their reset state.
This forces the A/D module to be turned off, and any
conversion is aborted.
The ADCON0 register, shown in Figure 9-1, controls
the operation of the A/D module. The ADCON1 regis-
ter, shown in Figure 9-2, configures the functions of the
port pins. The port pins can be configured as analog
inputs (RA3 can also be a voltage reference) or as dig-
ital I/O.
• A/D Result Register (ADRES)
• A/D Control Register 0 (ADCON0)
• A/D Control Register 1 (ADCON1)
U-0
—
PICmicro™
PIC16C62B/72A
ADON
R/W-0
bit0
Mid-Range
R = Readable bit
W = Writable bit
U = Unimplemented bit,
- n = Value at POR reset
read as ‘0’
Reference
DS35008B-page 49
Manual,