ATMEGA164PA-AU Atmel, ATMEGA164PA-AU Datasheet - Page 280

• Manufacturer Part Number: ATMEGA164PA-AU
• Description: MCU AVR 16KB FLASH 20MHZ 44TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA164PA-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: 2-Wire/SPI/USART
• Total Internal Ram Size: 1KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: TQFP
• Package: 44TQFP
• Family Name: ATmega
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

25.5
8272A–AVR–01/10
Boot Loader Lock Bits
Figure 25-2. Memory Sections
Note:
If no Boot Loader capability is needed, the entire Flash is available for application code. The
Boot Loader has two separate sets of Boot Lock bits which can be set independently. This gives
the user a unique flexibility to select different levels of protection.
The user can select:
• To protect the entire Flash from a software update by the MCU.
• To protect only the Boot Loader Flash section from a software update by the MCU.
• To protect only the Application Flash section from a software update by the MCU.
• Allow software update in the entire Flash.
See
can be set in software and in Serial or Parallel Programming mode, but they can be cleared by a
Chip Erase command only. The general Write Lock (Lock Bit mode 2) does not allow the pro-
gramming of the Flash memory by SPM instruction. Similarly, the general Read/Write Lock
(Lock Bit mode 3) does not allow reading nor writing by (E)LPM/SPM, if it is attempted.
164A/164PA/324A/324PA/644A/644PA/1284/1284P
Table 25-2 on page 281
1. The parameters in the figure above are given in
Boot Loader Flash Section
Boot Loader Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Program Memory
Program Memory
BOOTSZ = '11'
BOOTSZ = '01'
and
0x0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
0x0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
Table 25-3 on page 281
Boot Loader Flash Section
Boot Loader Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Table 25-10 on page
Program Memory
Program Memory
BOOTSZ = '10'
BOOTSZ = '00'
for further details. The Boot Lock bits
0x0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
0x0000
End RWW, End Application
Start NRWW, Start Boot Loader
Flashend
290.
280