DSPIC30F2011-20E/P Microchip Technology, DSPIC30F2011-20E/P Datasheet - Page 12
![IC DSPIC MCU/DSP 12K 18DIP](/photos/6/76/67657/18-dip_300mil__sml.jpg)
DSPIC30F2011-20E/P
Manufacturer Part Number
DSPIC30F2011-20E/P
Description
IC DSPIC MCU/DSP 12K 18DIP
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20ISO.pdf
(66 pages)
2.DSPIC30F2011-20ISO.pdf
(210 pages)
3.DSPIC30F2011-20ISO.pdf
(14 pages)
4.DSPIC30F2011-20ISO.pdf
(6 pages)
5.DSPIC30F2011-20ISO.pdf
(18 pages)
6.DSPIC30F2011-20IP.pdf
(26 pages)
Specifications of DSPIC30F2011-20E/P
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
12
Program Memory Size
12KB (4K x 24)
Program Memory Type
FLASH
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 8x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
18-DIP (0.300", 7.62mm)
For Use With
AC30F005 - MODULE SCKT DSPIC30F 18DIP/SOICACICE0202 - ADAPTER MPLABICE 18P 300 MIL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
dsPIC30F2011/2012
17. Module: I
18. Module: I
DS80450D-page 12
In 10-bit Addressing mode, some address
matches do not set the RBF flag or load the
receive register I2CxRCV, if the lower address
byte
particular, these include all addresses with the
form XX0000XXXX and XX1111XXXX, with the
following exceptions:
• 001111000X
• 011111001X
• 101111010X
• 111111011X
Work around
Ensure that the lower address byte in 10-bit
Addressing mode does not match any 7-bit
reserved addresses.
Affected Silicon Revisions
When the I
slave with and address of 0x102, the I2CxRCV
register content for the lower address byte is 0x01
rather
acknowledges both address bytes.
Work around
None.
Affected Silicon Revisions
A1
A1
X
X
matches
than
2
2
2
C
C
C module is configured as a 10-bit
0x02;
the
reserved
however,
addresses.
the
module
In
19. Module: I
Note:
When the I
I2CEN bit in the I2CCON register, the dsPIC DSC
device generates a glitch on the SDA and SCL
pins. This glitch falsely indicates “Communication
Start” to all devices on the I
a bus collision in a multi-master configuration.
Additionally, when the I2CEN bit is set, the S and
P bits of the I
‘0’, respectively, which indicate a “Communication
Start” condition.
Work arounds
To avoid this issue, either of the following two work
arounds can be implemented, depending on the
application requirements.
Work around 1:
In a single-master environment, add a delay
between enabling the I
transmission. The delay should be equal to or
greater than the time it takes to transmit two data
bits.
In the multi-master configuration, in addition to the
delay, all other I
nized and wait for the I
before initiating any kind of communication.
Work around 2:
In dsPIC DSC devices in which the I
multiplexed
precedence in the use of the pin, it is possible to
avoid this glitch by enabling the higher priority
module before enabling the I
Use the following procedure to implement this
work around:
1. Enable the higher priority peripheral module
2. Set up and enable the I
3. Disable the higher priority peripheral module
Affected Silicon Revisions
A1
X
that is multiplexed on the same pins as the I
module.
that was enabled in step 1.
Work around 2 works only for devices that
share the SDA and SCL pins with another
peripheral that has a higher precedence
over the port latch, such as the UART. The
priority is shown in the pin diagram located
in the data sheet. For example, if the SDA
and SCL pins are shared with the UART
and SPI pins, and the UART has higher
precedence on the port latch pin.
2
2
C
C module is enabled by setting the
2
with
C module are set to values ‘1’ and
2
C masters should be synchro-
© 2010 Microchip Technology Inc.
other
2
2
C module and the first data
C module to be initialized
2
2
modules
C module.
C bus, and can cause
2
C module.
2
C module is
that
have
2
C