ATTINY261V-10SU Atmel, ATTINY261V-10SU Datasheet - Page 73

• Manufacturer Part Number: ATTINY261V-10SU
• Description: IC MCU AVR 2K FLASH 10MHZ 20SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY261V-10SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Package: 20SOIC
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 10 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 16
• Interface Type: USI
• On-chip Adc: 11-chx10-bit
• Number Of Timers: 2
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRBC100 - REF DESIGN KIT BATTERY CHARGER770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATSTK505 - ADAPTER KIT FOR 14PIN AVR MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.3.1.1
11.3.2
2588E–AVR–08/10
External Clock Source
Prescaler Reset
Figure 11-2. Prescaler for Timer/Counter0
Note:
The prescaled clock has a frequency of f
Table 11-4 on page 85
The prescaler is free running, i.e. it operates independently of the Clock Select logic of the
Timer/Counter. Since the prescaler is not affected by the Timer/Counter’s clock select, the state
of the prescaler will have implications for situations where a prescaled clock is used. One exam-
ple of prescaling artifacts occurs when the timer is enabled and clocked by the prescaler (6 >
CSn2:0 > 1). The number of system clock cycles from when the timer is enabled to the first count
occurs can be from 1 to N+1 system clock cycles, where N equals the prescaler divisor (8, 64,
256, or 1024). It is possible to use the Prescaler Reset for synchronizing the Timer/Counter to
program execution.
An external clock source applied to the T0 pin can be used as Timer/Counter clock (clk
T0 pin is sampled once every system clock cycle by the pin synchronization logic. The synchro-
nized (sampled) signal is then passed through the edge detector.
equivalent block diagram of the T0 synchronization and edge detector logic. The registers are
clocked at the positive edge of the internal system clock (
high period of the internal system clock.
The edge detector generates one clk
= 6) edge it detects. See
PSR0
clk
T0
I/O
1. The synchronization logic on the input pins (
Synchronization
for details.
Table 11-4 on page 85
Clear
T
0
pulse for each positive (CSn2:0 = 7) or negative (CSn2:0
CLK_I/O
/8, f
for details.
T0)
CLK_I/O
is shown in
/64, f
clk
I/O
CLK_I/O
). The latch is transparent in the
Figure
Figure 11-3
/256, or f
11-3.
clk
T0
shows a functional
CLK_I/O
/1024. See
T0
). The
73