PIC18F1320-E/SS Microchip Technology, PIC18F1320-E/SS Datasheet - Page 13

• Manufacturer Part Number: PIC18F1320-E/SS
• Description: IC MCU FLASH 4KX16 EEPROM 20SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F1320-E/SS

• Program Memory Type: FLASH
• Program Memory Size: 8KB (4K x 16)
• Package / Case: 20-SSOP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163014, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 7 bit
• Package: 20SSOP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

2.0
2.1
The PIC18F1220 and PIC18F1320 devices can be
operated in ten different oscillator modes. The user can
program the configuration bits, FOSC3:FOSC0, in
Configuration Register 1H to select one of these ten
modes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. ECIO
2.2
In XT, LP, HS or HSPLL Oscillator modes, a crystal or
ceramic resonator is connected to the OSC1 and
OSC2 pins to establish oscillation. Figure 2-1 shows
the pin connections.
The oscillator design requires the use of a parallel cut
crystal.
 2004 Microchip Technology Inc.
Note:
LP
XT
HS
HSPLL
RC
RCIO
INTIO1
INTIO2
EC
OSCILLATOR
CONFIGURATIONS
Oscillator Types
Crystal Oscillator/Ceramic
Resonators
Use of a series cut crystal may give a
frequency out of the crystal manufacturer’s
specifications.
with PLL enabled
F
output on RA6 and I/O on RA7
and RA7
Low-Power Crystal
Crystal/Resonator
High-Speed Crystal/Resonator
High-Speed Crystal/Resonator
External Resistor/Capacitor with
External Resistor/Capacitor with
I/O on RA6
Internal Oscillator with F
Internal Oscillator with I/O on RA6
External Clock with F
External Clock with I/O on RA6
OSC
/4 output on RA6
OSC
OSC
/4 output
/4
FIGURE 2-1:
TABLE 2-1:
Capacitor values are for design guidance only.
These capacitors were tested with the resonators
listed below for basic start-up and operation. These
values are not optimized.
Different capacitor values may be required to produce
acceptable oscillator operation. The user should test
the performance of the oscillator over the expected
V
See the notes following Table 2-2 for additional
information.
Note 1: See Table 2-1 and Table 2-2 for initial
DD
Mode
HS
XT
and temperature range for the application.
C1
C2
2: A series resistor (R
3: R
455 kHz
2.0 MHz
PIC18F1220/1320
(1)
(1)
Typical Capacitor Values Used:
values of C1 and C2.
AT strip cut crystals.
F
16.0 MHz
XTAL
R
455 kHz
2.0 MHz
4.0 MHz
8.0 MHz
varies with the oscillator mode chosen.
S
Freq
(2)
Resonators Used:
CAPACITOR SELECTION FOR
CERAMIC RESONATORS
OSC2
OSC1
16.0 MHz
CRYSTAL/CERAMIC
RESONATOR OPERATION
(XT, LP, HS OR HSPLL
CONFIGURATION)
OSC1
56 pF
47 pF
33 pF
27 pF
22 pF
R
S
) may be required for
F
(3)
4.0 MHz
8.0 MHz
DS39605C-page 11
PIC18FXXXX
Sleep
OSC2
56 pF
47 pF
33 pF
27 pF
22 pF
To
Internal
Logic