PIC16F627A-I/SS Microchip Technology, PIC16F627A-I/SS Datasheet - Page 111
![IC MCU FLASH 1KX14 EEPROM 20SSOP](/photos/6/58/65895/150-20-ssop_sml.jpg)
PIC16F627A-I/SS
Manufacturer Part Number
PIC16F627A-I/SS
Description
IC MCU FLASH 1KX14 EEPROM 20SSOP
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F627A-IP.pdf
(180 pages)
3.PIC16F627A-IP.pdf
(8 pages)
4.PIC16F627A-IP.pdf
(22 pages)
5.PIC16F627A-ISO.pdf
(168 pages)
6.PIC16F648A-ISS.pdf
(178 pages)
Specifications of PIC16F627A-I/SS
Program Memory Type
FLASH
Program Memory Size
1.75KB (1K x 14)
Package / Case
20-SSOP
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
16
Eeprom Size
128 x 8
Ram Size
224 x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC16F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
224 B
Interface Type
SCI/USART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
16
Number Of Timers
3
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
Minimum Operating Temperature
- 40 C
Package
20SSOP
Device Core
PIC
Family Name
PIC16
Maximum Speed
20 MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
XLT20SS-1 - SOCKET TRANSITION 18DIP 20SSOPI3DBF648 - BOARD DAUGHTER ICEPIC3AC164307 - MODULE SKT FOR PM3 28SSOPAC162053 - HEADER INTERFACE ICD,ICD2 18DIPAC164018 - MODULE SKT PROMATEII 20SSOP
Data Converters
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC16F627A-I/SS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
14.11 In-Circuit Serial Programming
The PIC16F627A/628A/648A microcontrollers can be
serially programmed while in the end application circuit.
This is simply done with two lines for clock and data,
and three other lines for power, ground, and the
programming voltage. This allows customers to manu-
facture boards with unprogrammed devices and then
program the microcontroller just before shipping the
product. This also allows the most recent firmware, or
a custom firmware to be programmed.
The device is placed into a Program/Verify mode by
holding the RB6 and RB7 pins low while raising the
MCLR (V
specification). RB6 becomes the programming clock
and RB7 becomes the programming data. Both RB6
and RB7 are Schmitt Trigger inputs in this mode.
After Reset, to place the device into Programming/Verify
mode, the program counter (PC) is at location 00h. A 6-
bit command is then supplied to the device. Depending
on the command, 14 bits of program data are then
supplied to or from the device, depending if the
command was a load or a read. For complete details of
serial programming, please refer to the Programming
Specifications (DS41196).
A typical In-Circuit Serial Programming connection is
shown in Figure 14-18.
FIGURE 14-18:
2004 Microchip Technology Inc.
External
Connector
Signals
Data I/O
CLK
+5V
V
0V
PP
PP
) pin from V
To Normal
Connections
To Normal
Connections
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
IL
to V
IHH
PIC16F627A/628A/648A
V
V
RA5/MCLR/V
RB6/PGC
RB7/PGD
V
DD
SS
DD
(see programming
PP
Preliminary
PIC16F627A/628A/648A
14.12 Low Voltage Programming
The LVP bit of the configuration word, enables the low
voltage programming. This mode allows the microcon-
troller to be programmed via ICSP using only a 5V
source. This mode removes the requirement of V
be placed on the MCLR pin. The LVP bit is normally
erased to '1' which enables the low voltage program-
ming. In this mode, the RB4/PGM pin is dedicated to
the programming function and ceases to be a general
purpose I/O pin. The device will enter Programming
mode when a '1' is placed on the RB4/PGM pin. The
HV Programming mode is still available by placing V
on the MCLR pin.
If low-voltage Programming mode is not used, the LVP
bit should be programmed to a '0' so that RB4/PGM
becomes a digital I/O pin. To program the device, V
must be placed onto MCLR during programming. The
LVP bit may only be programmed when programming
is entered with V
programmed when programming is entered with RB4/
PGM.
It should be noted, that once the LVP bit is programmed
to 0, only high voltage Programming mode can be used
to program the device.
Note 1: While in this mode the RB4 pin can no
2: V
longer be used as a general purpose I/O
pin.
operations.
DD
IHH
must be 5.0V +10% during erase
on MCLR. The LVP bit cannot be
DS40044B-page 109
IHH
IHH
IHH
to