PIC16C717-I/SO Microchip Technology, PIC16C717-I/SO Datasheet - Page 87
![IC MCU OTP 2KX14 A/D PWM 18SOIC](/photos/6/76/67656/150-18-soic_sml.jpg)
PIC16C717-I/SO
Manufacturer Part Number
PIC16C717-I/SO
Description
IC MCU OTP 2KX14 A/D PWM 18SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F818-ISO.pdf
(6 pages)
2.PIC16C770-ISO.pdf
(220 pages)
3.PIC16C770-ISO.pdf
(6 pages)
4.PIC16C770-ISO.pdf
(8 pages)
Specifications of PIC16C717-I/SO
Core Size
8-Bit
Program Memory Size
3.5KB (2K x 14)
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Core Processor
PIC
Speed
20MHz
Connectivity
I²C, SPI
Number Of I /o
15
Program Memory Type
OTP
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 6x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
18-SOIC (7.5mm Width)
Controller Family/series
PIC16C
No. Of I/o's
16
Ram Memory Size
256Byte
Cpu Speed
20MHz
No. Of Timers
3
Processor Series
PIC16C
Core
PIC
Data Bus Width
8 bit
Data Ram Size
256 B
Interface Type
I2C, SPI, SSP
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
16
Number Of Timers
3 bit
Operating Supply Voltage
2.5 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
ICE2000, DM163022
Minimum Operating Temperature
- 40 C
On-chip Adc
6 bit
Data Rom Size
256 B
Height
2.31 mm
Length
11.53 mm
Supply Voltage (max)
5.5 V
Supply Voltage (min)
4 V
Width
7.49 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Other names
PIC16C717I/SO
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
FIGURE 9-15:
9.2.10
To initiate a START condition, the user sets the START
condition enable bit, SEN (SSPCON2<0>). If the SDA
and SCL pins are sampled high, indicating that the bus
is available, the baud rate generator is loaded with the
contents of SSPADD<6:0> and starts its count. If SCL
and SDA are both sampled high when the baud rate
generator times out (T
available, the SDA pin is driven low. The SDA transition
from high to low while SCL is high is the START condi-
tion. This causes the S bit (SSPSTAT<3>) to be set.
When the S bit is set, the baud rate generator is
reloaded with the contents of SSPADD<6:0> and
resumes its count. When the baud rate generator times
out (T
rent with the following events:
• The SEN bit (SSPCON2<0>) is automatically
• The baud rate generator is suspended leaving the
• The SSPIF flag is set.
FIGURE 9-16:
2002 Microchip Technology Inc.
cleared by hardware,
SDA line held low.
BRG
) the START condition is complete, concur-
I
CONDITION TIMING
2
C MASTER MODE START
SDA
SCL
BRG
value
BRG
reload
Write to SEN bit occurs here.
BAUD RATE GENERATOR TIMING WITH CLOCK ARBITRATION
FIRST START BIT TIMING
BRG
) indicating the bus is still
03h
SDA
SCL
DX
SCL de-asserted but slave holds
SCL low (clock arbitration)
02h
SCL is sampled high, reload takes
place, and BRG starts its count.
Advance Information
SDA = 1,
SCL = 1
T
BRG
01h
Set S bit (SSPSTAT<3>)
T
S
BRG
BRG decrements
(on Q2 and Q4 cycles)
00h (hold off)
DX-1
At completion of START bit,
Hardware clears SEN bit
9.2.10.1
If the user writes the SSPBUF when a START
sequence is in progress, the WCOL is set and the con-
tents of the buffer are unchanged (the write doesn’t
occur).
and sets SSPIF bit
Note:
Note:
PIC16C717/770/771
T
Write to SSPBUF occurs here
BRG
1st Bit
If at the beginning of START condition, the
SDA and SCL pins are already sampled
low, or if during the START condition, the
SCL line is sampled low before the SDA
line is driven low, a bus collision occurs.
Thus, the Bus Collision Interrupt Flag
(BCLIF) is set, the START condition is
aborted, and the I
its IDLE state.
WCOL STATUS FLAG
Because queueing of events is not
allowed, writing to the lower five bits of
SSPCON2 is disabled until the START
condition is complete.
SCL allowed to transition high
T
03h
BRG
02h
2nd Bit
2
C module is RESET into
DS41120B-page 85